AGC Pro31-M Operation And Maintenance Manual Download

Page: 3 / 19

Table of Contents

Scope: ........................................................................................................................................ 1

Receiving and Inspection: .......................................................................................................... 1

Frame Placement: ...................................................................................................................... 2

Normal Operation: ...................................................................................................................... 2

Closing the Frame: ..................................................................................................................... 3

Opening the Frame: ................................................................................................................... 4

Frame Assembly Instructions: .................................................................................................... 4

Operator Maintenance: ............................................................................................................... 8

Parts List: ................................................................................................................................... 8

Spindle Nut Assembly ......................................................................................................... 9

Pushtube Assembly........................................................................................................... 10

Follower Roller Assembly .................................................................................................. 11

Pro3 Terminal Components .............................................................................................. 12

Pro3 Plate and Frame Gaskets ......................................................................................... 13

Eastern Factory

Western Factory

10129 Piper Lane

9109 SE 64

Avenue

Bristow, Virginia 20136

Portland, Oregon 97206

Phone 703-257-1660

Phone 503-774-7342

Fax 703-330-7940

Fax 503-774-2550

800-825-8820

800-715-8820

www.AGCHeatTransfer.com

Revised 08/27/13

Summary of Contents for Pro31-M




















Search results

Summary of Contents for Pro31-M

Reviews:

Related manuals for Pro31-M

Brands by name

Popular brands

AGC Pro31-M, Operation And Maintenance Manual

Search results

Summary of Contents for Pro31-M

Reviews:

Related manuals for Pro31-M

Brands by name

Popular brands