background image

Performance Verification

22

Test 6. Bandwidth Check (100 mV/A range)

29

Increase the generated frequency to 100 kHz.

30

Measure the current in the coil (

I

c

) and record the current reading 

in 

Table 11

.

NOTE

The current in the coil must be 

¡

 10 mA.  Increase the generated amplitude if 

necessary to achieve a current of at least 10 mA.

31

Measure the voltage output (

V

PROBE

) by the probe on DMM 2, and 

record in 

Table 11

.

32

Do the calculations specified in 

Table 11

 to determine if the probe 

passes the test.

Table 10 AC Current Measurement Accuracy Record (100 mV/A range)

Measurement

Recorded Value

Current in Coil (

I

C

)

Probe Output Voltage (

V

PROBE

)

Calculate Maximum Probe Output Voltage As:

VP

ROBEMAX

 = (I

C

 * 10 * 100 mV/A * 1.03)

Calculate Minimum Probe Output Voltage As:

V

PROBEMIN

 = (I

C

 * 10 * 100 mV/A * 0.97)

Probe Passes Test if: 

V

PROBEMIN

 

¤

 V

PROBE

 

¤ 

V

PROBEMAX

Table 11 Bandwidth Record

 

(100 mV/A range)

Measurement

Recorded Value

Current in Coil (

I

C

)

Probe Output Voltage (

V

PROBE

)

Calculate Maximum Probe Output Voltage As:

V

PROBEMAX

 = (I

C

 * 10 * 100 mV/A * 1.03)

Calculate Minimum Probe Output Voltage As:

V

PROBEMIN

 = (I

C

 * 10 * 100 mV/A * 0.97) * 0.707

Probe Passes Test if:

V

PROBEMIN

 

¤

 V

PROBE

 

¤

 V

PROBEMAX

Summary of Contents for 1146B

























Reviews: