background image

4

 

 

In This Book

This book is the service guide for the 16910A and 16911A logic analyzer modules. 

This service guide has eight chapters.

Chapter 1, “General Information,” beginning on page 9 contains information 
about the module and includes accessories for the module, specifications and 
characteristics of the module, and a list of the equipment required for servicing 
the module.

Chapter 2, “Preparing for Use,” beginning on page 15 tells how to inspect and 
prepare the module for use. 

Chapter 3, “Testing Logic Analyzer Performance,” beginning on page 19 gives 
instructions on how to test the performance of the module. 

Chapter 4, “Calibrating,” beginning on page 61 contains calibration instructions 
for the module (if required).

Chapter 5, “Troubleshooting,” beginning on page 63 contains flowcharts for 
troubleshooting the module and an explanations of the self-tests. 

Chapter 6, “Replacing Assemblies,” beginning on page 83 explains how to replace 
the module and assemblies of the module and how to return them to Agilent 
Technologies.

Chapter 7, “Replaceable Parts,” beginning on page 89 lists replaceable parts, 
shows an exploded view, and gives ordering information. 

Chapter 8, “Theory of Operation,” beginning on page 97 explains how the logic 
analyzer works.

Summary of Contents for 16900 Series









































































































Reviews: