background image

76

16901A Logic Analysis System Service Guide

7

Replaceable Parts

 

Ordering Replaceable Parts

To order a part, visit us on the web at 

www.parts.agilent.com

 or call us in the United States at 

1- 877- 447- 7278. Or, you can contact your nearest Agilent 
Technologies Sales Office for assistance. To locate a sales 
office near you, go to 

www.agilent.com/find/contactus

.

Exchange Assemblies

Some assemblies are part of an exchange program with 
Agilent Technologies.

The exchange program allows you to exchange a faulty 
assembly with one that has been repaired and performance 
verified by Agilent Technologies.

After you receive the exchange assembly, return the defective 
assembly to Agilent Technologies. A United States customer 
has 30 days to return the defective assembly. If you do not 
return the defective assembly within the 30 days, Agilent 
Technologies will charge you an additional amount. This 
amount is the difference in price between a new assembly 
and that of the exchange assembly. For orders not 
originating in the United States, contact your nearest Agilent 
Technologies Sales Office for information. To locate a sales 
office near you, go to 

www.agilent.com/find/contactus

.

For more information on returning assemblies go to 

“Returning Assemblies” 

on page 74.

Summary of Contents for 16901A









































































































Reviews: