Agilent Technologies 8719ES Programmer'S Manual Download | Manualshive

Page: 311 / 541

background image

3-2

Chapter 3

GPIB Programming

Analyzer Command Syntax

Analyzer Command Syntax

Code Naming Convention

The analyzer GPIB commands are derived from their front-panel key titles (where
possible), according to this naming convention:

Simple commands are the first four letters of the function they control, as in

POWE

, the

command name for power. If the function label contains two words, the first three
mnemonic letters are the first three letters of the first word, and the fourth mnemonic
letter is the first letter of the second word. For example,

ELED

is derived from electrical

delay.

If there are many commands grouped together in a category, as in markers or plotting pen
numbers, the command is increased to 8 letters. The first four letters are the category label
and the last four letters are the function specifier. As an example, category pen numbers
are represented by the command

PENN

, which is used in combination with several

functions such as

PENNDATA

,

PENNMEMO

.

The code naming guidelines, listed in

, are used in order to:

• make commands more meaningful and easier to remember

• maintain compatibility with other products (including the 8510 series analyzers)

NOTE

There are times when these guidelines are not followed due to technical
considerations.

«
...
309
310
311
312
313
...
»

Summary of Contents for 8719ES






























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8719ES

Brand: PAT Pages: 55

Brand: PAT Pages: 31

Brand: ICS Pages: 2

Brand: CAISSON Pages: 5

Brand: Felix Instruments Pages: 102

Brand: IEI Technology Pages: 85

CellaCast PA8 Series

Brand: Keller Pages: 12

Brand: M-system Pages: 13

Brand: TA Instruments Pages: 7

Brand: Gearx Pages: 19

Brand: Clavitech Pages: 56

VBOX Touch Motorsport V1

Brand: Racelogic Pages: 15

Brand: PRESIDIUM Pages: 86

Brand: Seca Pages: 280

Brand: Zico Pages: 3

Brand: Hach Pages: 252

Brand: NARDA Pages: 8

Brand: JDS Uniphase Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands