298
Chapter 7
Fixture Simulator
Evaluating Balanced Devices (balance-unbalance conversion function)
Steps for Balance-Unbalance Conversion
NOTE
When using three test ports, perform a full three-port calibration on the test ports to be
used. When using four test ports, perform a full four-port calibration.
Extend the calibration plane, if necessary, by using the port extension function or network
de-embedding function. For more on the port extension and network de-embedding
functions, see “Extending the Calibration Plane Using Network De-embedding” on
page 285.
Step 1.
Press
.
Step 2.
Press
Fixture Simulator
.
Step 3.
Press
Topology
.
Step 4.
Press
Device
.
Step 5.
Select the balanced/unbalanced topology.
Softkey
Function
SE-Bal
Establishes port 1 on the DUT as an unbalanced port and port 2 as a balanced
port
Bal-Bal
Establishes both port 1 and port 2 on the DUT as balanced ports
SE-SE-Bal
Establishes port 1 and port 2 on the DUT as unbalanced ports and port 3 as a
balanced port
Step 6.
Select each port on the analyzer to which a port on the DUT is connected.
⋅
When you have selected
SE-Bal
in Step 5:
Softkey
Function
Port 1 (se)
Selects a port on the analyzer from among
1
,
2
,
3
, and
4
for connection to
logical 1 (Port a in Figure 7-8)
Port 2 (bal)
Selects two ports on the analyzer from among
1-2
,
1-3
,
1-4
,
2-1
,
2-3
,
2-4
,
3-1
,
3-2
,
3-4
,
4-1
,
4-2
, and
4-3
for connection to logical port 2 (Port b and Port c in
⋅
When you have selected
Bal-Bal
in Step 5:
Softkey
Function
Port 1 (bal)
Selects two ports on the analyzer from among
1-2
,
1-3
,
1-4
,
2-1
,
2-3
,
2-4
,
3-1
,
3-2
,
3-4
,
4-1
,
4-2
, and
4-3
for connection to logical port 1 (Port a and Port b in
Port 2 (bal)
Selects two ports on the analyzer from among
1-2
,
1-3
,
1-4
,
2-1
,
2-3
,
2-4
,
3-1
,
3-2
,
3-4
,
4-1
,
4-2
, and
4-3
for connection to logical port 2 (Port c and Port d in
⋅
When you have selected
SE-SE-Bal
Softkey
Function
Port 1 (se)
Selects a port on the analyzer from among
1
,
2
,
3
, and
4
for connection to
logical 1 (Port a in Figure 7-8)
Summary of Contents for E5070B
