Agilent Technologies E8362C Service Manual Download

Page: 112 / 382

4-32

Service Guide E8364-90038

Troubleshooting

PNA Series Microwave Network Analyzers

Measurement System Troubleshooting

E8362C, E8363C, E8364C

A phase lock problem is due to either:

•

faulty RF signal generation (caused by the A12 source 20, A21 SOMA 50, A23 and A24 SOMA 70)

•

faulty LO signal generation (caused by the A8, A10, A11, A17 or A18 board)

RF Signal Troubleshooting

To isolate a broadband RF signal generation failure, check the test port output power:

1. Connect a power meter and power sensor to Port 1 of the analyzer.

2. On the analyzer, press

Preset

, set the

Center Frequency

2 GHz

, and the

Frequency Span

0 Hz

. Note

the power reading displayed on the power meter. The output power, as indicated on the power meter,
should be approximately



12 dBm ±5 dB for an analyzer with no hardware options or -17 dBm ±5 dB for

an analyzer with options.

NOTE

In the unlocked state, the analyzer will “search” for the reference signal.

3. Connect the power sensor to Port 2 and set trace to measure S

. Note the power reading displayed on

the power meter. The power meter reading should be the same as was measured at Port 1.

•

If the power level is low at both test ports the problem is either the A12 source 20 or the A21 SOMA 50.
Continue with

“Checking the A12 Output, All Bands”

Checking the A12 Output, All Bands

1. Disconnect W1 from A12.

2. Connect a cable to A12 and measure the output power. A power level of a -17 dBm ±5 dB indicates the

A12 assembly is functioning normally.

3. If the output power of A12 is at or below the minimum power level, replace the A12 source 20 assembly.

4. If the output power is normal, reconnect cable W1 to A12.

Checking the A21 Output (E8363C and E8364C Only)

1. Disconnect W2 from A21.

2. Connect a cable to A21 and measure the output power. A power level of a -7 dBm ±5 dB indicates the

A21 assembly is functioning normally.

3. If the output power of A21 is at or below the minimum power level, replace the A21 SOMA 50 assembly.

4. If the output power is normal, reconnect cable W2 to A21.

Checking the A10 5 MHz Reference Output, All Bands

1. Refer to the block diagram at the end of this chapter and to

“Top Cables–All, All Options Except 080” on

page 6-16

. Locate flexible cable W31, at the A10 frequency reference board.

2. Disconnect W31 from A10J10.

3. Connect the spectrum analyzer to A10J10.

4. The spectrum analyzer should measure a signal at 5 MHz.

5. If no 5 MHz signal is present, replace the A10 frequency reference board. Refer to

“Removing and

Replacing the A6, A8, A9, and A10 Boards” on page 7-18

Summary of Contents for E8362C































































































































































































































































































































































































Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands

Agilent Technologies E8362C, Service Manual

Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands