manualshive.com logo in svg

Agilent Technologies E8362C, Service Manual

The Agilent Technologies E8362C is a cutting-edge device designed for accurate and efficient testing of electronic components. Discover all its features and functionalities by accessing the comprehensive Service Manual which can be freely downloaded from our website. Harness the power of this product and revolutionize your testing process.

Share
Download
background image

Service Guide E8364-90038

2-5

PNA Series Microwave Network Analyzers

     General Product Information

E8362C, E8363C, E8364C

Analyzer Options Available

Option 083, Frequency Converter Measurement Application

This option adds an intuitive and easy-to-use user interface, advanced calibration choices that provide 
exceptional amplitude and phase accuracy, and control of external signal sources for use as local oscillators 
(both fixed and swept-LO measurements are supported). A graphical set-up dialog box lets you quickly set 
up the instrument for single or dual conversion devices. This set-up screen also helps you calculate and 
choose where mixing and image products will fall.

Option 099, Firmware Upgrade

This upgrade provides the latest revision of firmware for the PNA series network analyzers on CD-ROM. This 
firmware is user installable. The installation requires a USB CD-ROM drive (see 

“CD-RW Drive” on page 2-7

) 

or an external computer connected to a Local Area Network (LAN).

This firmware is also available on the Internet at the Agilent website: 

http://www.agilent.com/find/pna

. 

(Select your analyzer’s model number in this website to view available upgrades.)

Option 1CM, Rack Mount Flange Kit for Instruments without Handles

Option 1CM provides a rack mount kit that contains a pair of flanges, rack mount rails, and the necessary 
hardware to mount the analyzer in an equipment rack with 482.6 mm (19 inches) horizontal spacing.

Additional kits may be ordered from Agilent. Refer to 

“Rack Mount Kits and Handle Kits” on page 6-86

 for 

the part numbers.

Option 1CP, Rack Mount Flange Kit for Instruments with Handles

Option 1CP provides a rack mount kit that contains a pair of flanges (cut to adapt to handles), rack mount 
rails, and the necessary hardware to mount the analyzer in an equipment rack with 482.6 mm (19 inches) 
horizontal spacing.

Additional kits may be ordered from Agilent. Refer to 

“Rack Mount Kits and Handle Kits” on page 6-86

 for 

the part numbers.

Option 897, Built-In Tests for Commercial Calibration

This option enables performance tests that are built into the analyzer that enable you to perform ISO 9001 
commercial calibration of your analyzer. Refer to 

“Service and Support Options” on page 2-11

 for a 

description of the commercial calibration.

Option 898 Built-In Tests for Standards Compliant Calibration

This option enables performance tests that are built into the analyzer that enable you to perform ISO 17025 
and ANSI Z540 standards compliant calibration of your analyzer. Refer to 

“Service and Support Options” on 

page 2-11

 for a description of the standards compliant calibrations.

Option H08, Pulse Measurement Capability

This option enables additional firmware and hardware within the analyzer to allow you to perform pulse 
measurements with you PNA. This option requires that Option H11 also be installed.

Summary of Contents for E8362C































































































































































































































































































































































































Reviews:

No comments

Related manuals for E8362C

Lambrecht 252 Operating Instructions preview
252
Brand: Lambrecht Pages: 5
Keithley 3390 Adjustment Manual preview
3390
Brand: Keithley Pages: 25
Keithley 199 Quick Reference Manual preview
199
Brand: Keithley Pages: 49
Camille Bauer SINEAX AM2000 Device Handbook preview
SINEAX AM2000
Brand: Camille Bauer Pages: 62
Taber 5135 Operating Instructions Manual preview
5135
Brand: Taber Pages: 53
ICS Schneider Messtechnik Snap 41 Instruction Manual And Safety Information preview
Snap 41
Brand: ICS Schneider Messtechnik Pages: 40
CAS Corporation TW-100 Service Manual preview
TW-100
Brand: CAS Corporation Pages: 20
Primes Cube L1 Original Instructions Manual preview
Cube L1
Brand: Primes Pages: 56
Aqualytic AL250T-IR Instruction Manual preview
AL250T-IR
Brand: Aqualytic Pages: 140
Qonnex 2-WIRE EMM.630CT-MID Quick Start preview
2-WIRE EMM.630CT-MID
Brand: Qonnex Pages: 2
Eastwood Guitars WARREN ELLIS SIGNATURE TENOR BARITONE Setup Manual preview
WARREN ELLIS SIGNATURE TENOR BARITONE
Brand: Eastwood Guitars Pages: 4
Fluke 87V Ex Calibration Manual preview
87V Ex
Brand: Fluke Pages: 32
A-CUBE USB-1 User Manual preview
USB-1
Brand: A-CUBE Pages: 25
Endress+Hauser Cerabar S PMC71 Functional Safety Manual preview
Cerabar S PMC71
Brand: Endress+Hauser Pages: 48
OHAUS MB27 Instruction Manual preview
MB27
Brand: OHAUS Pages: 64
Würth 0715 53 325 Translation Of The Original Operating Instructions preview
0715 53 325
Brand: Würth Pages: 28
Hach Lange ORBISPHERE 3100 User Manual preview
Lange ORBISPHERE 3100
Brand: Hach Pages: 47
IFM SM2 00 Series Operating Instructions Manual preview
SM2 00 Series
Brand: IFM Pages: 45

Brands by name

Popular brands

Load more brands