Agilent Technologies E8362C Service Manual Download

Page: 314 / 382

7-58

Service Guide E8364-90038

Repair and Replacement Procedures

PNA Series Microwave Network Analyzers

Removing and Replacing the A36 and A37 60-dB Source Step Attenuators (Option UNL)

E8362C, E8363C, E8364C

Removing and Replacing the A36 and A37 60-dB Source Step Attenuators
(Option UNL)

Tools Required

•

T-10 TORX driver (set to 9 in-lb)

•

T-20 TORX driver (set to 21 in-lb)

•

5/16-inch open-end torque wrench (set to 10 in-lb)

•

ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-26

for this procedure.

1. Disconnect the power cord.

2. Remove the outer cover. Refer to

“Removing the Covers” on page 7-6

. Position the analyzer bottom side

up and raise the receiver deck as shown. Refer to

“Raising the Receiver Deck” on page 7-8

if necessary.

3. Identify the step attenuator to be removed. To replace the attenuator, the bracket holding the attenuator,

detector (E8363C/E8364C) or fixed pad (E8362C), and bias tee must be removed.

4. Disconnect the ribbon cable (item

①

) from the appropriate attenuator.

5. With a 5/16-inch torque wrench, disconnect the two semirigid cables (item

➁

) from the appropriate

step attenuator, two semirigid cables (item

③

) from the detector (or fixed pad), and two semirigid cables

(item

④

) from the bias tee.

6. Disconnect the stranded control cable (item

⑤

) and the flexible cable (item

⑥

) from the appropriate

detector (E8363C/E8364C only) and the stranded bias tee cable (item

⑦

) from A16 test set motherboard.

(Release the bias tee cable such that it can be removed with the bias tee.)

7. With a T-10 TORX driver, remove the three mounting screws (item

⑧

) from the bracket holding the

attenuator, detector (or fixed pad), and bias tee.

CAUTION

Be careful not to damage the center pins of the semirigid cables. Some flexing of the cables
is necessary to remove the assembly. Do not over-bend the semirigid cables.

8. Remove the bracket from the analyzer with the attenuator, detector (or fixed pad), and bias tee attached.

Observe the

CAUTION

above.

9. With a T-10 TORX driver, remove the two mounting screws holding the attenuator.

Replacement Procedure

1. Reverse the order of the removal procedure using the existing attenuator ribbon cable.

2. Perform the post-repair adjustments, verifications, and performance tests that pertain to this removal

procedure. Refer to

Table 7-2 on page 7-82

Summary of Contents for E8362C































































































































































































































































































































































































Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands

Agilent Technologies E8362C, Service Manual

Search results

Summary of Contents for E8362C

Reviews:

Related manuals for E8362C

Brands by name

Popular brands