Agilent Technologies E8362C Service Manual Download | Manualshive

Page: 49 / 382

background image

Service Guide E8364-90038

3- 17

PNA Series Microwave Network Analyzers

Tests and Adjustments

E8362C, E8363C, E836C

Preliminary Checks

Cable Connector Repeatability Check

NOTE

The connector repeatability measurement should be done at the test port as well as at the
end of the test port cable.

1.

With the test port cable still connected to Port 1, connect a broadband load to the other end of the cable.

2.

Press

Preset

.

3.

On the

Channel

menu, click

Average

. In the

Average

dialog box, click the

Average ON

check box. In the

Average Factor

box, type 100 or click the arrows to select 100. Click

OK

.

4.

Wait for the analyzer to average the measurement 100 times (approximately five seconds).

5.

To normalize the data trace:

a. On the

Trace

menu, click

Math/Memory

.

b. In the

Math/Memory

dialog box, click the

Data->Memory

button.

c. In the

Data Math

list, select

Data/Memory

.

d. Under

Trace View Options

, make sure

Data Trace

is selected.

e. Click

OK

6.

To adjust the display scale:

a. On the

Scale

menu, click

Scale

.

b. In the

Scale Per Division

box, click the arrow to select

0.5 dB

.

c. In the

Level

box under

Reference

click the arrow to select

0 dB

.

d. Click

OK

.

7.

Disconnect and then reconnect the cable to the test port. Tighten the connection to the specified torque
for the connector type.

8.

On the

Channel

menu, click

Restart

Avg

.

9.

Look at the trace for spikes or modes.

10. To re-normalize the data trace of the reconnected cable:

a. On the

Trace

menu, click

Math/Memory

.

b. In the

Math/Memory

dialog box, click the

Data->Memory

button.

c. Click

OK

.

11. Repeat steps 7 through 9 at least three times to look for modes. Modes appear when a harmonic of the

source fundamental frequency is able to propagate through the cable or connector. It is helpful to print a
plot of the trace each time to compare several connections. If any mode appears each time the cable is
connected and reconnected, measurement integrity will be affected.

For a typical response of cable connector repeatability, see

Figure 3-7

.

12. For the Port 2 Check, connect the cable (with the load attached) to Port 2 and repeat steps 2 through 11.

«
...
47
48
49
50
51
...
»

Summary of Contents for E8362C































































































































































































































































































































































































Reviews:

No comments

Related manuals for E8362C

Brand: OfiTE Pages: 24

Brand: Facom Pages: 42

Brand: Oceanic Pages: 152

Brand: Kaiterra Pages: 8

Brand: Kaiterra Pages: 12

Brand: Underground Magnetics Pages: 48

Brand: Motortech Pages: 142

Brand: OHAUS Pages: 71

Brand: Kawai Pages: 36

Brand: PCE Health and Fitness Pages: 11

Brand: Scaletron Pages: 63

Brand: Ecodhome Pages: 12

Brand: Kawai Pages: 28

Brand: THORLABS Pages: 63

Brand: THORLABS Pages: 20

Brand: Kurzweil Pages: 35

Cobra SMARTsense Chloride Ion

Brand: PHYWE Pages: 4

SUPER-CUTAWAY DIY ELECTRIC GUITAR KIT

Brand: Gear4music Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands