manualshive.com logo in svg

Agilent Technologies E8362C, Service Manual

The Agilent Technologies E8362C is a cutting-edge device designed for accurate and efficient testing of electronic components. Discover all its features and functionalities by accessing the comprehensive Service Manual which can be freely downloaded from our website. Harness the power of this product and revolutionize your testing process.

Share
Download
background image

Contents

Service Guide E8364-90038

Contents-

3

Assembly Replacement Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Getting Started with Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Check the Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Troubleshooting Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Power Up Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Power Supply Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Front Panel Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Front Panel Keypad and RPG Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
A2 Display Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Checking the USB Board  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
A3 Front Panel Interface Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Rear Panel Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Checking the USB Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
Checking the SERIAL (RS-232), PARALLEL (1284-C), or VGA Port  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
Checking the GPIB Port  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
LAN Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Measurement System Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24

Before you begin—consider: Where do you see a problem? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Verifying the A, B, R1, and R2 Traces (Standard S-Parameter Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26
Where to Begin Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27
Checking the Source Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
Checking the Signal Separation Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38
Checking the Receiver Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42
Checking the Frequency Offset Group (Option 080). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44

Instrument Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49

E8362C Overall Block Diagram, No Options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49
E8362C Overall Block Diagram, All Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-51
E8363C and E8364C Overall Block Diagram, No Options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53
E8363C and E8364C Overall Block Diagram, All Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-55

5

Theory of Operation

Information in This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Chapter Five at-a-Glance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Network Analyzer System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Functional Groups of the Network Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Source Group Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Band Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
A8 Fractional-N Synthesizer Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
A17 L.O. Multiplier/Amplifier 10 (LOMA 10). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
A18 Multiplier/Amplifier 20 (MA 20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
A19 Splitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
A20 L.O. Distribution Assembly (LODA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
A10 Frequency Reference Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
A11 Phase Lock Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
A12 Source 20  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
A21 Source Multiplier/Amplifier 50 (SOMA 50) (E8363C and E8364C Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
A16 Test Set Motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

Signal Separation Group Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16

A22 Switch Splitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16

Summary of Contents for E8362C































































































































































































































































































































































































Reviews:

No comments

Related manuals for E8362C

GE Sievers 500 RL Quick Start Manual preview
Sievers 500 RL
Brand: GE Pages: 8
GE Moisture Image 1 Series Startup Manual preview
Moisture Image 1 Series
Brand: GE Pages: 110
GE DigitalFlow GS868 Service Manual preview
DigitalFlow GS868
Brand: GE Pages: 74
GE DigitalFlow GS868 Startup Manual preview
DigitalFlow GS868
Brand: GE Pages: 81
Baker Hughes PanaFlow Z1G User Manual preview
PanaFlow Z1G
Brand: Baker Hughes Pages: 59
Baker Hughes PanaFlow Z1G Installation Instructions preview
PanaFlow Z1G
Brand: Baker Hughes Pages: 2
Panametrics CTF878 Service Manual preview
CTF878
Brand: Panametrics Pages: 67
Panametrics CTF878 Startup Manual preview
CTF878
Brand: Panametrics Pages: 108
GE Transport PT878 Abridged Manual preview
Transport PT878
Brand: GE Pages: 97
Igema G Installation And Operating Instructions Manual preview
G
Brand: Igema Pages: 30
z-laser ZX Series Operator'S Manual preview
ZX Series
Brand: z-laser Pages: 62
janitza UMG 96 RM-EL Installation Manual preview
UMG 96 RM-EL
Brand: janitza Pages: 12
LaserLiner PowerCross-Laser 8 S Operating Instructions Manual preview
PowerCross-Laser 8 S
Brand: LaserLiner Pages: 64
LaserLiner ClimaHome-Check Plus Manual preview
ClimaHome-Check Plus
Brand: LaserLiner Pages: 10
LaserLiner MeterMaster Plus Quick Start Manual preview
MeterMaster Plus
Brand: LaserLiner Pages: 104
LaserLiner ThermoSpot Operating Instructions Manual preview
ThermoSpot
Brand: LaserLiner Pages: 52
LaserLiner LaserRange-Master T2 Manual preview
LaserRange-Master T2
Brand: LaserLiner Pages: 52
LaserLiner ArcoMaster 40 Quick Start Manual preview
ArcoMaster 40
Brand: LaserLiner Pages: 5

Brands by name

Popular brands

Load more brands