manualshive.com logo in svg

Agilent Technologies E8362C, Service Manual

The Agilent Technologies E8362C is a cutting-edge device designed for accurate and efficient testing of electronic components. Discover all its features and functionalities by accessing the comprehensive Service Manual which can be freely downloaded from our website. Harness the power of this product and revolutionize your testing process.

Share
Download
background image

Contents-

4

Service Guide E8364-90038

Contents

A25 and A26 Test Port Couplers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
A23 and A24 Detectors (E8363C and E8364C Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
30-dB Fixed Attenuators (E8362C Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
A36 and A37 60-dB Source Step Attenuators (Option UNL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
A38 and A39 Bias Tees (Option UNL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
A43 and A44 35-dB Receiver Step Attenuators (Option 016) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Option 014 Configurable Test Set  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18

Receiver Group Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

A27, A28, A29, and A30 Receiver First Converters (Mixers). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
A49 IF Multiplexer Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
A31, A32, A33, and A34 Receiver Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
A6 SPAM Board (Analog Description) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
A35 Receiver Motherboard  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23

Frequency Offset Group Operation (Options 080 and 081) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24

A9 Fractional-N Synthesizer Board (Option 080) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
A13 Frequency Offset Receiver Assembly (Option 080)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24
A45 and A46 Reference Transfer Switches (Option 081)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24

IF Access Group (Option H11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26

A47 RF Path Coupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
A48 LO Path Coupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
A49 IF Multiplexer Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26
Rear-Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26

Digital Processing and Digital Control Group Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28

Front Panel Subgroup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30
Data Acquisition and Processing Subgroup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31

Power Supply Group Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33

6

Replaceable Parts

Information in This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

How to Use the Replaceable Parts Listings in This Chapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Chapter Six at-a-Glance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Assembly Replacement Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Rebuilt-Exchange Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Replaceable Parts Listings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

Front Panel Assembly, Front Side, All Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Front Panel Assembly, Back Side, All Options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Top Assemblies, All Options Except 080  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Top Cables–All, All Options Except 080 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
Top Assemblies, All Options Including 080 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
Top Cables–All, All Options Including 080 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
Bottom Assemblies, No Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
Bottom Semi-Rigid Cables, No Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24
Bottom Assemblies, Option UNL  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26
Bottom Semi-Rigid Cables, Option UNL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-28
Bottom Assemblies, Option 014 and Options 014/080 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-30
Bottom Semi-Rigid Cables, Options 014 and 014/080. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-32
Bottom Assemblies, Options UNL/014 and UNL/014/080  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-34
Bottom Semi-Rigid Cables, Options UNL/014 and UNL/014/080. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36
Bottom Assemblies, Options UNL/016 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-38

Summary of Contents for E8362C































































































































































































































































































































































































Reviews:

No comments

Related manuals for E8362C

Hammond Skx PRO Reference Manual preview
Skx PRO
Brand: Hammond Pages: 754
Cannon CAV 4.2 Operation Manual preview
CAV 4.2
Brand: Cannon Pages: 64
Cannon CAV 4.1 Operation Manual preview
CAV 4.1
Brand: Cannon Pages: 73
QuadTech 1855 Instruction Manual preview
1855
Brand: QuadTech Pages: 76
Vanguard Instruments Company WRM-10P User Manual preview
WRM-10P
Brand: Vanguard Instruments Company Pages: 62
Vanguard Instruments Company IRM-5000P User Manual preview
IRM-5000P
Brand: Vanguard Instruments Company Pages: 58
YOKOGAWA Vigilantplant NFBU200-S Series User Manual preview
Vigilantplant NFBU200-S Series
Brand: YOKOGAWA Pages: 24
horiba LAQUA-PC1100 Instruction Manual preview
LAQUA-PC1100
Brand: horiba Pages: 117
Sequid DTDR-65 Operation Manual preview
DTDR-65
Brand: Sequid Pages: 111
Dennerle Duomat Evolution DeLuxe Instructions For Use Manual preview
Duomat Evolution DeLuxe
Brand: Dennerle Pages: 27
Seaward PAC3760 PLUS Quick Reference Manual preview
PAC3760 PLUS
Brand: Seaward Pages: 2
SRS Labs SXMCMTU64 Installation Instructions Manual preview
SXMCMTU64
Brand: SRS Labs Pages: 11
IFM SI500A Operating Instructions Manual preview
SI500A
Brand: IFM Pages: 13
TFA KLIMA GUARD 30.5010 Instruction Manual preview
KLIMA GUARD 30.5010
Brand: TFA Pages: 22
Astute Medical ASTUTE140 User Manual preview
ASTUTE140
Brand: Astute Medical Pages: 86
sauermann HST Quick Start Manual preview
HST
Brand: sauermann Pages: 7
Caird Technology HRV VX3+ Manual preview
HRV VX3+
Brand: Caird Technology Pages: 29
Fluke Biomedical Victoreen 07-494 Operator'S Manual preview
Victoreen 07-494
Brand: Fluke Biomedical Pages: 34

Brands by name

Popular brands

Load more brands