Agilent Technologies E8364-60102 Installation Note Download

Page: 5 / 22

Installation Note E8364-90011

Items Included in the Upgrade Kit

Table 1

lists the parts included in this upgrade kit, Agilent part number E8364-60102. Check

the contents of your kit against this list. If any item is missing or damaged, contact Agilent
Technologies. Refer to

“Getting Assistance from Agilent” on page 3

Table 1

Contents of Option UNL Upgrade Kit (E8364-60102)

Ref.
Desig.

Description

Qty

Part

Number

The following parts are required for all analyzers

Installation note (this document)

E8364-90011

Machine screw, M3.0 x 8 CWPNTX (for attaching attenuators)

0515-0372

Machine screw, M2.5 x 14 CWPNTX (for attaching bias tees)

0515-2141

Cable clamp

1400-1439

A36, A37

60-dB step attenuator

33325-60012

A38, A39

Bias tee (cable included)

5087-7233

Ribbon cable (for A36 step attenuator)

8121-0819

Ribbon cable (for A37 step attenuator)

8121-0119

W51

RF cable, A22 switch splitter to A36 step attenuator

E8364-20055

W52

RF cable, A22 switch splitter to A37 step attenuator

E8364-20056

W55

RF cable, A38 bias tee to A25 test port 1 coupler

E8364-20051

W56

RF cable, A39 bias tee to A26 test port 2 coupler

E8364-20052

The following parts are required for only analyzers without Option 014 installed

RF cable, A23 detector to A28 channel R1 mixer

E8364-20079

RF cable, A24 detector to A29 channel R2 mixer

E8364-20080

W53

RF cable, A36 step attenuator to A38 bias tee

E8364-20077

W54

RF cable A37 step attenuator to A39 bias tee

The following parts are required for only analyzers with Option 014 installed

Lower front panel overlay (Option UNL/014)

E8364-80011

W70

RF cable, RCVR R1 IN to A28 channel R1 mixer

E8364-20049

W71

RF cable, RCVR R2 IN to A29 channel R2 mixer

E8364-20050

W81

RF cable, A36 step attenuator to Port 1 SOURCE OUT

E8364-20053

W82

RF cable, A37 step attenuator to Port 2 SOURCE OUT

E8364-20054

W83

RF cable, PORT 1 CPLR THRU to A38 bias tee

E8364-20039

W84

RF cable, PORT 2 CPLR THRU to A39 bias tee

E8364-20040

Summary of Contents for E8364-60102























Search results

Summary of Contents for E8364-60102

Reviews:

Related manuals for E8364-60102

Brands by name

Popular brands

Agilent Technologies E8364-60102, Installation Note

Search results

Summary of Contents for E8364-60102

Reviews:

Related manuals for E8364-60102

Brands by name

Popular brands