background image

U1253A Quick Start Guide

Performing Voltage Measurements

Performing Current Measurements

C A U T I O N

If the current is 

≤ 

440 mA, connect the red and black test leads to input terminals 

µA.mA (red)

 and 

COM (black).

If the current is > 440 mA, connect the red and black test leads to input terminals 

A (red)

 and 

COM (black)

.

Measuring AC voltage

1

Set the rotary switch to 

For 

 and 

 mode, 

press 

 to ensure 

 is 

shown on the display.

2

Connect the red and black test 
leads to input terminals 

V. mV (red)

 

and 

COM (black)

 

respectively.

3

Probe the test points and read 
the display.

4

Press 

 to display dual 

measurements. Parameter can 
be switched consecutively.

Measuring DC voltage

1

Set the rotary switch to 

 

or 

. Ensure that 

 is 

shown on the display. 

2

Connect the red and black test 
leads to input terminals 

V. mV (red)

 and 

COM (black)

 

respectively.

3

Probe the test points and read 
the display.

4

Press

 to display dual 

measurements. Parameter can 
be switched consecutively.

Measuring AC current

1

Set the rotary switch to 

 

or 

. Press 

 to 

ensure 

 is shown on the 

display.

2

Connect the red and black test 
leads to input terminals 

µA.mA (red)

 

and 

COM (black) 

or 

A (red)

 

and 

COM (black) 

respectively.

3

Probe the test points in series 
with the circuit and read the 
display.

Measuring DC current

1

Set the rotary switch to 

 

or 

. Ensure that 

 is 

shown on the display. 

2

Connect the red and black test 
leads to input terminals 

µA.mA (red)

 

and 

COM (black) 

or 

A (red)

 

and 

COM (black) 

respectively.

3

Probe the test points in series 
with the circuit and read the 
display.

U1253A QSG.fm  Page 2  Tuesday, September 23, 2008  9:44 AM

Summary of Contents for U1253A







Reviews: