background image

Tilt Stand

Safety Information

Tilt stand at 60

°

 

Tilt stand at 30

°

This meter is safety-certified in compliance with 
EN/IEC 61010-1:2001, UL 61010-1 Second Edition and 
CAN/CSA 22.2 61010-1 Second Edition, Category III 
1000 V, Pollution Degree II. Use with standard or 
compatible test probes.

Safety Notices

CAUTION

 notice denotes a hazard. It calls 

attention to an operating procedure, practice, or 
the like that, if not correctly performed or adhered 
to, could result in damage to the product or loss of 
important data. Do not proceed beyond a 

CAUTION

 notice until the indicated conditions are 

fully understood and met.

WA R N I N G

A WARNING notice denotes a hazard. It calls atten-
tion to an operating procedure, practice, or the like 
that, if not correctly performed or adhered to, could 
result in personal injury or death. Do not proceed 
beyond a WARNING notice until the indicated condi-
tions are fully understood and met.

Safety Symbols

CAT III
1000 V

Category III 1000 V overvoltage protection

Double insulation

Earth ground

Caution, risk of danger

Caution, risk of electric shock

For further safety information details, refer to the 

Agilent U1253A True RMS OLED 

Multimeter User’s and Service Guide

.

© Agilent Technologies, Inc., 2008
First Edition, October 1, 2008

                                                                   U1253-90011 

Agilent Technologies

U1253A QSG.fm  Page 6  Tuesday, September 23, 2008  9:44 AM

Summary of Contents for U1253A







Reviews: