background image

33

Adjusting Level Accuracy (Calibration)

Without moving your checking setup, make a mark on the 2 X $ halfway between A1 and A2 
(call it C).  The laser must be calibrated to bring the beam to the center mark C.
IMPORTANT: Before calibrating, ensure that the instrument housing is level by placing a 
small carpenter’s level on top of the unit, parallel with the beam.  Do not move the unit: only 
adjust the single centerline leg or trivet point until the housing is level.
Do not enter calibration mode or attempt adjustment unless it is planned to change accuracy.  
Accuracy adjustment should be performed carefully, by personnel who understand basic 
adjustment principles.
If you’ve made changes you do not wish to save, turn the laser off.
Accessing Calibration through the Set Up Menu

Turn the laser off, and the turn the laser on again.
When the AGL start-up screen is displayed, press the 

+

and 

ENT

buttons simultaneously.  Hold until the Set Up 

screen appears (after the Battery Check).

The cursor and highlighted text indicate the active menu 
step.

Use the 

+

or 

buttons to move up or down the menu.  

Move down to 

CALIBRATION

and press 

ENT

.

Confirm the step 

MAIN AXIS

by pressing 

ENT

.

WAIT

The screen will show 

WAIT

.

SET

When SET appears, the height of the laser beam can be 
adjusted to the center point C.
Do this by using the Remote, so the laser is not disturbed 
during adjustment.  It will also allow you to stand at stake 
A and move the beam until it is at C.

Use the 

Center Line

button on the remote to move the 

beam up; use the 

Standby (ZZZ) 

button on the Remote 

to move the beam down.

Summary of Contents for GradeLight 3000









































Reviews: