background image

5

SPECIFIC SAFETY RULES FOR HVLP 

SPRAYERS

OBSERVE ALL WARNINGS!

WARNING: Do not use guns for spraying 
flammable materials.

WARNING: Be aware of any hazards presented 
by the material being sprayed, and consult 
the markings on the material container or the 
information supplied by the manufacturer of 
the material to be sprayed. 

WARNING: Do not spray any material where the 
hazard is not known.

WARNING: Do not clean guns with flammable 
solvents with a flash-point below 55°C.

NOTE: A non-flammable solvent is here defined 
as one which has a flash-point above 55°C.

WARNING: This appliance cannot be used by 
children under 18 years old or persons with 
reduced physical, sensory or mental capabilities 
or lack of experience or knowledge of the safe 
operation of the appliance. 

WARNING: Children may not play with this 
appliance.

WARNING: Cleaning and user maintenance shall 
not be made by children.

WARNING: This appliance shall be disconnected 
from its power source during service and when 
replacing parts. The plug must remain removed, 
and must be removed in such a way that an 
operator can check from any of the points to 
which he has access that the plug remains 
removed.

This equipment is for professional use only.

WARNING: FIRE AND EXPLOSION HAZARD. 
Take all precautions to avoid sources of sparks 
and ignition when spraying. Keep the machine 
at least 8 meters away from the spraying 
operation. 

Wear Protective Equipment At All Times.
Always use a respirator, eye protection and 
protective clothing and gloves. 

CAUTION:
• 

Do not use the sprayer with flammable 
paint.

• 

Do not use guns for spraying flammable 
materials.

• 

Do not clean guns with flammable 
solvents.

• 

Beware of any hazards presented by 
the material being sprayed and consult 
the markings on the container or the 
information supplied by the manufacturer 
of the material to be sprayed, including 
requirements for the use of personal 
protective equipment.

• 

Do not spray any material where the 
hazard is not known

The appliance is not to be used by children or 
persons with reduced physical, sensory or mental 
capabilities, or lack of experience and knowledge, 
unless they have been given supervision or 
instruction and children being supervised not to 
play with the appliance.

EXPLOSION RISK FROM 

HALOGENATED HYDROCARBON 

SOLVENTS

 

Never use halogenated hydrocarbon solvents in 
this machine. Contact with aluminum parts may 
cause an explosion.  Some of the most common 
of these solvents are: Carbontetrachloride, 
Chlorobenzene, Dichloroethane, Dichloroethyl 
E t h e r,   E t h y l b r o m i d e ,   E t h y l c h l o r i d e ,   & 

Summary of Contents for T328

















Reviews: