background image

 
 

AGRETO LoadCounter II M 

© AGRETO electronics GmbH  

 

page:19 

11

 

 Warranty 

In addition to the statutory warranty, the following warranty conditions apply to 

the AGRETO LoadCounter II M: 

 

The AGRETO electronics GmbH guarantees the function and repairs or 

replaces all the parts that have a material or manufacturing damage within 

the warranty period. 

 

Warranty services will be performed by the AGRETO electronics GmbH. 

 

The decision on the existence of a warranty claim is sole responsibility of 

the AGRETO electronics GmbH. 

 

The warranty period begins with the first accounting to an end customer 

and ends 5 years from this date of invoice. 

 

Prerequisite for warranty service are the presentation of the original invoice 

and compliance with all elements of this instruction manual. 

 

Excluded from warranty are wear, normal wear and tear, damage due to 

misuse, negligence or accident. 

 

When processing a warranty claim transport costs incurred will be charged 

to the buyer. 

 

12

 

 Disposal 

Dispose of the device as part of the final shutdown or parts of it 

environmentally friendly and sorted (metal to the respective metal 

scrap, plastic to the plastic waste, etc. - do not dispose as 

household waste)! 

Detailed information can be found in directive 2002/96 / EC 
 

Summary of Contents for BZLC0010





















Reviews: