background image

2

RULES FOR SAFE OPERATION

The  following  safety  precautions  are  suggested.  This 
broadcast spreader is designed, engineered and tested to 
offer reasonably safe and effective service, provided it is 
operated in strict accordance with these instructions. Failure 
to do so may result in personal injury. Always observe the 
rules of safe operation.

1. 

Do not allow anyone to operate the broadcast spreader 
without proper instructions.

2. 

Do  not  permit  children  to  operate  the  broadcast 
spreader.

3. 

Wear  eye  and  hand  protection  when  handling  and 
when applying lawn or garden chemicals.

4. 

Read the chemical label instructions and cautions for 
handling  and  applying  the  chemicals  purchased  for 
spreading.

5. 

Keep  all  nuts,  bolts  and  screws  tight  to  be  sure 
equipment is in safe working condition.

6. 

Follow  maintenance  and  lubrication  instructions  as 
outlined in this manual. 

CARTON CONTENTS

LOOSE PARTS IN CARTON  

1. 

Handle Tube (long)

2. 

Braces (2)

3. 

Flow Control Mount Bracket

4. 

Flow Control Arm

5. 

Handle Tube (short)

6. 

Flow Control Rod

7. 

Leg Stand Tube

8. 

Wheels (2)

9. 

Hopper Assembly

 

Hardware Package (not shown)

2

6

5

1

7

9

3

4

8

LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS.  IT 
MEANS — ATTENTION!  BECOME ALERT!  YOUR SAFETY IS INVOLVED.

Summary of Contents for 45-02103













Reviews: