Agri-Fab LST42C Owner'S Manual Download

Page: 15 / 36

INSTaLLING CLuTCH/IDLer aSSeMBLY

This section covers the installation of the Clutch/Idler

assembly to tractors with attachment clutches that are
either rod operated (p. 15), cable operated (p. 17) or

electric (p. 19). Use the appropriate instructions for your
tractor.

roD oPeraTeD MaNuaL aTTaCHMeNT CLuTCH

STeP 29: (See FIGure 29)
• Move the attachment clutch lever on the dash panel to

the disengaged (down) position.

• Screw the trunnion (CC) onto the end of the snow

thrower engagement rod.

• Locate the clutch arm (where the mower clutch rod

was connected) underneath the right hand side the

tractor, just to the inside of the suspension arm.

there is an extension

attached to the clutch lever, the

extension, bolt and nut must be removed and stored
with the mower deck.

IMPorTaNT: re-attach the extension

to the clutch

lever before reinstalling the mower deck.

• Position the engagement rod to the inside of the

clutch arm and insert the drilled end of the rod
through the arm. Secure with a 5/64" hairpin cotter

(DD).

FIGure 29

rIGHT SIDe VIew

ENGAGEMENT ROD

5/64" HAIRPIN
COTTER (DD)

TRACTOR'S CLUTCH ARM

SUSPENSION ARM

TRUNNION (CC)

REMOVE EXTENSION,
BOLT AND NUT
(IF PRESENT)

STeP 30: (See FIGure 30)
• Attach the two suspension arms to the inside of the

clutch/idler assembly using two 5/16" x 3/4" hex bolts
(C), 5/16" washers (Q) and 5/16" nylock nuts (Y) for
each arm. Place the washers between the arms and
the assembly frame.

• Insert a tensioning chain through the hole shown and

attach the end link to the spring on the lower idler arm.

FIGure 30

5/16" x 3/4"
HEX BOLT (C)

5/16" NYLOCK
NUT (Y)

TENSIONING CHAIN (JJ)

5/16" WASHER (Q)

FIGure 31

SToP

Did you choose the correct drive belt for
your tractor? Using the wrong length belt
may cause premature bearing or belt failure.

HEX BOLTS

DRIVE BELT

FLAT IDLER
PULLEY

(#46989)

STeP 31: (See FIGure 31)
• Two different length drive belts are included with

your snow thrower. Tractors with manual attachment
clutches and dual front deck suspension brackets use
the 55" drive belt with

#46989

printed on the outside

of the belt.

Do NoT uSe the other belt.

• Slightly loosen the hex bolt next to the flat idler pulley.

Install the drive belt down between the hex bolt and the
flat idler pulley with the flat side of the belt against the
pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.

Summary of Contents for LST42C





































Search results

Summary of Contents for LST42C

Reviews:

Related manuals for LST42C

Brands by name

Popular brands

Agri-Fab LST42C, Owner'S Manual

Search results

Summary of Contents for LST42C

Reviews:

Related manuals for LST42C

Brands by name

Popular brands