MANUTENZIONE
8
MAINTENANCE
RMU
8-7
8.4
Dopo le prime 100 ore di lavoro
Personale richiesto: 1 OPERATORE
Sostituire l'olio della scatola ingranaggi procedendo
nel modo seguente:
• Svitare il tappo di scarico 1 (Fig. 8-4), se necessario
smontare temporaneamente la protezione 2.
• Fare uscire tutto l’olio.
• Avvitare il tappo di scarico 1.
• Svitare il tappo di carico 3 ed immettere olio tipo
ROLOIL “VARIAX-EP/85W140 GL-5”, o equiva-
lente, nella quantità indicata in tabella 8-2.
• Avvitare il tappo di carico 3 e rimontare la prote-
zione 2 (se precedentemente smontata).
8.5
Ogni 300 ore di lavoro
Sostituire l'olio della scatola ingranaggi seguendo le
indicazioni del punto 8.4.
8.6
Cinghie di trasmissione
8.6.1 Tensionamento
Personale richiesto: 1 TECNICO QUALIFICATO
Per tendere le cinghie procedere nel modo seguente:
• Togliere il coperchio del carter copricinghie.
• Allentare i dadi 1 (Fig. 8-5) quanto basta per otte-
nere lo scorrimento della scatola ingranaggi.
• Svitare i dadi 2A e 2B.
• Svitare il dado 3A ed avvitare il dado 3B in ugual
misura.
• Serrare i dadi 1, 2A, 2B precedentemente allentati.
• Controllare che sia soddisfatta la condizione di Fig.
8-6.
• Rimontare il coperchio del carter copricinghie.
8.6.2 Sostituzione
Personale richiesto: 1 TECNICO QUALIFICATO
Per sostituire le cinghie procedere nel modo seguente:
• Togliere il coperchio del carter copricinghie.
• Allentare i dadi 1 (Fig. 8-5) quanto basta per otte-
nere lo scorrimento della scatola ingranaggi.
• Avvitare il dado 3A.
• Spingere la scatola ingranaggi fino ad ottenere
l’allentamento delle cinghie.
• Sostituire le cinghie.
• Tendere le cinghie come da punto 8.6.1.
• Rimontare il coperchio del carter copricinghie.
8.4
After the first 100 working hours
Required staff: 1 OPERATOR
Replace the gearbox oil as follows:
• Unscrew the drain plug 1 (Fig. 8-4), if necessary
remove temporarily the cover 2.
• Drain the oil completely.
• Tighten the drain plug 1.
• Unscrew the plug 3 and fill ROLOIL “VARIAX-EP/
85W140 GL-5” lube or equivalent in the quantity
shown in Table 8-2.
• Tighten the plug 3 and reinstall the cover 2 (if previ-
ously removed).
8.5
Every 300 working hours
Replace the oil in the gearbox as described at point
8.4.
8.6
Driving belts
8.6.1 Tightening
Required staff: 1 TRAINED TECHNICIAN
In order to tighten the belts, proceed as follows:
• Remove the cover of the belt protection casing.
• Loosen the nuts 1 (Fig. 8-5) until the gearbox slides
freely.
• Loosen the nuts 2A and 2B.
• Unscrew the nut 3A and tighten the nut 3B equally.
• Tighten the nuts 1, 2A, 2B previously loosened.
• Make sure the condition shown in Fig. 8-6 is
respected.
• Reinstall the cover of the belt protection casing.
8.6.2 Replacement
Required staff: 1 TRAINED TECHNICIAN
In order to replace the belts, proceed as follow:
• Remove the cover of the belt protection casing.
• Loosen the nuts 1 (Fig. 8-5) until the gearbox slides
freely.
• Tighten the nut 3A.
• Push the gearbox until the belts are slack.
• Replace the belts.
• Tighten the belts as indicated at point 8.6.1.
• Reinstall the cover of the belt protection casing.
Summary of Contents for RMU 1250
