background image

https://www.agrotkindustrial.com/

sales@agrotkindustrial.com

13

Handling safety

OSHA 1910.266 Appendix A - First-aid Kits

Source:

http://www.osha.gov/pls/oshaweb/owadisp.show_document?p_table=STANDARDS&p_id=9863.

Accessed: 16 Dec 09

The first-aid kit information below was directly obtained from OSHA regulations. Having a kit

available at the job site is required by OSHA for logging operations and is highly recommended by

AGT Manufacturing.

The following list sets forth the minimally acceptable number and type of first-aid

supplies for first-aid kits required under paragraph (d)(2) of the logging standard. The

contents of the first-aid kit listed should be adequate for small work sites, consisting of

approximately two to three employees. When larger operations or multiple operations

are being conducted at the same location, additional first-aid kits should be provided at

the work site or additional quantities of supplies should be included in the first-aid kits:

1.

Gauze pads (at least 4 x 4 inches).

2.

Two large gauze pads (at least 8 x 10 inches).

3.

Box adhesive bandages (band-aids).

4.

One package gauze roller bandage at least 2 inches wide.

5.

Two triangular bandages.

6.

Wound cleaning agent such as sealed moistened towelettes.

7.

Scissors.

8.

At least one blanket.

9.

Tweezers.

10. Adhesive tape.

11. Latex gloves.

12. Equipment such as resuscitation bag, airway, or pocket mask.

13. Two elastic wraps.

14. Splint.

15. Directions for requesting emergency assistance.

Summary of Contents for AGT-SSRC72





















Reviews: