background image

 

 

 

 

 

 

 

AIBASE 4-in-1 Motion Sensor   

 

 

 

 

 

Content: 

4-in-1 Motion Sensor   ........................................................................................................

错误

!

未定义书签。

 

1. Product Introduction .............................................................................................................................. 2 
2. Product Appearance .............................................................................................................................. 2 
3. Specification ........................................................................................................................................... 3 
4. Features/Capabilities: ............................................................................................................................ 4 
5. Installation Position and Notes .............................................................................................................. 4 
6. Product Installation ................................................................................................................................ 5 
7. Product Usage ........................................................................................................................................ 6 
7.3.1 Association Command ...................................................................................................................... 8 
7.3.2 Configuration Command Parameters ............................................................................................... 8 
8. Attention .............................................................................................................................................. 10 

Summary of Contents for HA-ZW-5SABC












Reviews: