background image

5.13.2 Housing Assembly

1. The lens support screw is provided to support

the rail assembly. Adjustment will only be
necessary if the rail assembly is rotated at angle
other than horizontal. If the screw head is not
touching the cover when the cover is installed,
loosen the screw until it does. See FIGURE 18.

FIGURE 18  Support Screw Adjustment

2. Replace the cover onto the base assembly by

grasping the cover and gently pushing it over the
end cap and o-ring. Make sure the o-ring is not
pinched. The safety cable can be routed between
the cover and the base. See FIGURE 19

FIGURE 19  Replacing the Cover

3. Align the cover holes with the base assembly

holes and replace the two M4 screws and
washers. This secures the cover onto the rest of
the housing.

NOTE: Make sure the breather hole is located at the
bottom of the housing. If it is not, remove both front
retaining rings and the face plate. Orient them so the
breather hole is located at the bottom and the gaps in
the retaining rings are centered over the breather hole.
See FIGURE 20.

FIGURE 20  Location of the Breather Hole

11

Lens 

Support

Screw

Base Assembly

Cover

End Cap

Front Face Plate

Retaining Ring 

Breather Hole (centered)

 

 

 

 

 

 

 

 

Summary of Contents for HS9385 Series













Reviews: