background image

4

5

INSTALLATION

This installation should be made by a
qualified service person and conform to all
local codes.

5.1

Model Designation

HS9385-6

115VAC, 50/60Hz

108 to 132

50W

HS9385-2

24VAC, 50/60Hz

21.6 to 26.4 50W

HS9385-5

230VAC, 50/60Hz 207 to 253

50W

1

Heater requires 40 watts.

Do Not Exceed 30VAC Input on 24VAC models.
Operation above 30VAC violates low voltage
operation (Class 2 Specifications). Normal operation is
24VAC.

Maximum Camera/Lens Size: Accepts cameras 
up to 102W x 71H mm (4.0 x 2.8in.), lenses up to
102W x 92H mm (4.0 x 3.6in.), and camera/lens
combinations up to 345L mm (13.6in.).

5.2 Tools Required

• Flat blade screwdriver
• Phillips head screwdriver
• M7 (7mm) hex wrench or socket
• M3 (3mm) hex wrench
• M4 (4mm or 5/32in.) hex wrench
• M8 (8mm or 5/16in.) hex wrench
• Adjustable wrench
• Wire cutter/stripper/crimper tool

5.3 Hardware Required

• M6 screws (X3) or 1/4in. screws (X3)
• M6 nuts (X3) or 1/4in. nuts (X3)
• M6 lock washers (X3) or 

1/4in. lock washers (X3)

5.4 Cable Requirements

Video Transmission (Coaxial)

Cable Type

RG-59/U (Runs < 1000ft)
RG-11/U (Runs < 2000ft)

Cable Size

Outside diameter between 4.6mm
and 7.9mm (0.181in. and 0.312in.)

Cable Shape

Round

Shield

93% Braided Copper Shield

Center Conductor

Stranded Copper Center

DC Resistance

15

/1000ft (RG-59/U)

6

/1000ft (RG-11/U)

Cable Impedence

75

Agency Rating

UL

Environmental

Outdoor rated

Temperature Rating

80 °C (176 °F)

Sources

Belden 9259
Belden 9238

Input Power Cord - North American

Cable Type

SJTOW-A Rated

Cable Size

Outside diameter between 4.3mm
and 11.9mm (0.170in. and 0.470in.)

Cable Shape

Round

Conductors

3 conductor version and 
2 conductor version

Agency Rating

UL/C.S.A., UL VW-1

Environmental

Outdoor rated

Temperature Rating

105 °C

Voltage Rating

300 V

Sources

Belden 19506
Belden 19509
Northwire 573939

Input Power Cord - European

Cable Type

H05RN-F3G0.75 and
H05RN-F3G1.00

Cable Size

Outside diameter between 4.3mm
and 11.9mm (0.170in. and 0.470in.)

Cable Shape

Round

Conductors

3 conductor version and 
2 conductor version

Agency Rating

VDE

Environmental

Outdoor rated

Sources

Olflex 1600252
Olflex 1600253

Model No.

Rated

Input

Range

Power

Consumption

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for HS9385 Series













Reviews: