background image

12

 

Li

-

ion Battery Pack 

 

NOTE:  Your  battery  pack  is  not 
fully  charged  at  the  time  of  pur-
chase.  Be  sure  to  charge  battery 
before first use.

 

 

 

Batteries  should  be  charged  in 
ambient  temperatures  between  0°
C (32°F) and 40°C (104°F). Charg-
ing outside this range will result in 
either less than full charge or dam-
age to the battery pack.

 

 

Allow  the  charger  to  cool  when 
charging  more  than  two  battery 
packs consecutively.

 

 

Do not insert finger/body parts or 
foreign  objects  into  contact  area 
of charger.

 

1.

 

Place charger in a relatively cool 
and well

-

ventilated area.

 

2.

 

Plug  charger  into  the  AC  outlet. 
CAUTION: Ensure that the pow-
er source to be utilized conforms 
to  the  power  requirement  speci-
fied on the charger nameplate.

 

3.

 

Turn  the  battery  upside

-

down 

and slide the battery into charger 
while  keeping  the  alignment 
marks  line  up.  Slide  the  forward 
in  the  direction  of  the  arrow.  Do 
not  force  battery:  It  should  slide 
easily  into  place  with  nominal 
force.  Any  difficulty  doing  so 
indicates incorrect alignment.

 

 

 

 

 

 

 

 

4.

 

If  the  power  lamp  (RED)  does 
not light immediately or goes out 
soon  after  the  charger  is 
plugged  in,  consult  a 

Signature 

Series

 authorized dealer.

 

5.

 

During  charging,  the  charging 
lamp  (GREEN)  will  start  flash-
ing.  When  charging  is  complet-
ed,  an  internal  electronic  switch 
will automatically be triggered to 
prevent overcharging.

 

-

  Charging  will  not  start  if  the 

battery pack is warm. For exam-
ple,  immediately  after  high  duty 
cycle  operation.  The  YELLOW 
standby  lamp  will flash  until the 
battery  temperature  drops  to 
where safe charging is possible.

 

6.

 

If the temperature of the battery 
pack  is  0

o

C  (32

0

F)  or  less, 

charging  will  take  longer  to  fully 
charge  the  battery  pack  than 
standard  charging  time.  At  this 
low temperature, even when the 
battery  is  fully  charged,  it  will 
have  approximately  50%  of  the 
power  of  a  fully  charged  battery 
at  normal  operation  tempera-
tures.

 

7.

 

Once  the  battery  is  fully 
charged,  the  GREEN  lamp  will 
light  to  indicate  the  charger  has 
entered  into  a  trickle  charge 
mode.

 

 

CHARGING THE BATTERY PACK

 

Summary of Contents for Signature Series

























Reviews: