background image

6

 

Service

 

 

Tool  service  must  be  per-
formed only by qualified repair 
personnel.

  Service  or  mainte-

nance  performed  by  unqualified 
personnel could result in a risk of 
injury.

 

 

When servicing an AIMCO Sig-
nature  Series  Precision  Clutch 
tool  it  is  important  to  use 
AIMCO  Signature  Series  parts 
and  all  work  should  be  under-
taken  by  a  qualified  AIMCO 
Signature  Series  Authorized 
Technician.

 Use of unauthorized 

parts or work performed by a non

-

authorized  technician  will  void 

warranty and may create a risk of 
damage to the tool, risk of electric 
shock, or injury to a user.

 

 

 

Battery Charger

 

 

Caution:  To  reduce  risk  of  injury, 
charge only the authorized batteries. 
Other  types  of  batteries  may  burst, 
causing  personal  injury  and  dam-
age.

 

 

Before using battery charger, read 
all  instructions  and  cautionary 
markings  on  batteries,  chargers, 
and products using batteries.

 

 

Do  not  allow  anything  to  cover  or 
clog the charger vents.

 

 

Do  not  expose  charger  to  rain, 
snow, or wet conditions.

 

 

To  reduce  the  risk  of  damage  to 
electric plug and cord, pull by plug 
rather than cord when disconnect-
ing charger.

 

 

Use  of  an  attachment  not  recom-
mended  or  sold  by  the  manufac-
turer  may  result  in  a  risk  of  fire, 
electric  shock,  or  injury  to  per-
sons.

 

 

Make  sure  cord  for  charger  is  lo-
cated so that it will not be stepped 
on,  tripped  on,  tripped  over,  or 
otherwise subjected to damage or 
stress.

 

Additional Safety Rules

 

 

Do not abuse the power cord. Nev-
er use the cord to carry the charger. 
Keep  cord  away  from  heat,  oil, 

 

water,  sharp  edges,  or  moving 
parts.  Replace  damaged  cords  im-
mediately.

 

 

Do  not  operate  charger  if  it  has 
been damaged in any way. Take it 
to  a  qualified  service  center  for 

 

repair.

 

 

To  reduce  risk  of  electric  shock, 
unplug  charger  from  outlet  before 
attempting  any  maintenance  or 
cleaning.  Turning  off  controls  will 
not reduce this risk.

 

 

Do not disassemble charger or bat-
tery cartridge. Take it to a qualified 
service  center  when  repair  is  re-
quired.  Incorrect  reassembly  may 
result  in  a  risk  of  electric  shock  or 
fire.

 

 

Battery Pack

 

 

Do  not  charge  battery  pack  when 
temperature  is  below  0°C  (32°F) 
or above 40°C (104°F).

 

 

Do not attempt to use a step

-

down 

transformer,  an  engine  generator, 
or DC power receptacle.

 

 

Do  not  short the  battery  pack: Do 
not  touch  the  terminals  with  any 
conductive  material.  Avoid  storing 
battery  cartridge  in  a  container 
with  other  metal  objects  such  as 
nails, coins, paper clips, etc.

 

 

Do not expose battery cartridge to 
water  or  rain.  A  battery  short  can 
cause  large  current  flow,  over-
heating,  possibly  burns,  and even 
a breakdown.

 

 

Do  not  store  the  machine  and 
battery  pack  in  locations  where 
the  temperature  may  reach  or 
exceed 50°C (122°F).

 

 

Do not incinerate the battery pack 
even  if  it  is  severely  damaged  or 
completely  worn  out.  The  battery 
pack can explode in a fire.

 

 

Be  careful  not  to  drop,  shake,  or 
strike the battery.

 

Summary of Contents for Signature Series

























Reviews: