29
(1) Choice among terminal block output alternatives
・
Choose output signal alternatives for use in Output Terminal Block OUT1~5.
・
This setting is common among WORK No. 1~4.
Initial Setting
ＯＵＴ１：
ＣＯＵＮＴ ＯＫ
ＯＵＴ２：
ＣＯＵＮＴ ＮＯＫ
ＯＵＴ３：ＯＫ （
Fastening
ＯＫ）
ＯＵＴ４：ＮＯＫ （
Fastening
ＮＯＫ）
ＯＵＴ５：ＢＵＺＺＥＲ （
Buzzer Output
）
Alternatives
（
Pick up 5 among the following alternatives
）
●
ＣＯＵＮＴ ＯＫ
●
ＣＯＵＮＴ ＮＯＫ
●
ＯＫ
●
ＮＯＫ
●ＢＵＺＺＥＲ
●ＷＡＲＮＩＮＧ
●Ｗ．１．Ｃ．ＯＫ ●Ｗ．２．Ｃ．ＯＫ ●Ｗ．３．Ｃ．ＯＫ ●Ｗ．４．Ｃ．ＯＫ
●ＣＹＣＬＥ ＣＯＵＮＴ １ ●ＣＹＣＬＥ ＣＯＵＮＴ ２
●ＰＵＬＳＥ ＮＯＳ．１ ●ＰＵＬＳＥ ＮＯＳ．２
Particulars
COUNT OK
・ＣＯＵＮＴ
ＯＫ
external output signal
・
Output duration can be set on Count OK Output Time Timer.
COUNT NOK
・ＣＯＵＮＴ NＯＫ
external output signal. This signal will be output when the predetermined
fastening number has not been attained before judgment.
・
This output signal will be kept on during COUNT NOK.
・
This output signal remains on until the remaining fastening number has been cleared by
adding fastening operation or OK condition has resulted by using PASS or NOK status has
been cleared by RESET inputting.
OK
・
Fastening OK external output signal
・
Output duration can be set on Fastening OK Output Time Timer.
NOK (Fastening NOK)
・
This signal will be output at the time of an initial or cycle error.
・
This output signal remains on until Fastening OK will be given by performing additional
fastening operation or error conditions have been cleared by RESET or Fastening NOK
RESET inputting.
ＢＵＺＺＥＲ（
output for Buzzer
）
・
Use this option when an external buzzer will be used.
・
Signal output ON timing is the same as the buzzer mounted on System. This buzzer does not
produce sound at the time of key operation.
ＷＡＲＮＩＮＧ（
alarm output
）
・
This signal will be output from the Warning Output Timer’s time-out to Count OK or to Line
Control Timer’s time-out.
Ｗ．※．Ｃ．ＯＫ （ＷＯＲＫ ※ ＣＯＵＮＴ ＯＫ） ※：１～４
・
Select this output when COUNT OK output becomes necessary on a Work No. basis.
ＣＹＣ．ＣＯＵＮＴ １／２ ＰＵＬＳ．ＮＯＳ． １／２
・
This signal will be output when Cycle Count or Cumulative Pulse attained the value preset
using Tool management OUT SET.
