SPECIFICATIONS
Motor .............................. 120V, 50/60 Hz
Blade Diameter .............. 9" ( 22.9 cm)
Speeds ........................... 2
Control ........................... Rotary Knob
Air Flow Distribution ....... 360
°
Variable
Approvals ....................... UL listed. Close mesh fan guard meets
OSHA requirements.
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
DESCRIPTION
The Airking 9" (22.9 cm) Pivot features 3-speed rotary knob
operation, 360
°
adjustable tilt stand. The 9" ( 22.9 cm) 3-paddle
blade is driven by a permanent prelubricated motor with a 6' (1.83
m) 18/3 cordset.
OPERATING INSTRUCTIONS & PARTS MANUAL
GENERAL SAFETY INFORMATION
1. Make certain that the power source conforms to the electrical
requirements of the fan.
2. The power cord is equipped with a three-prong grounded plug
that must be inserted into a matching receptacle. Under no
circumstances must the grounding prong be cut off the plug.
Where a two-prong wall receptacle is encountered, it must be
replaced with a properly grounded three-prong receptacle
installed in accordance with the National Electrical Code (NEC)
and all applicable local codes and ordinances. This work must
be done only by a qualified electrician, using copper wire only.
WARNING: USE OF A THREE-PRONG TO TWO-PRONG
ADAPTER IS NOT RECOMMENDED. IMPROPER CONNECTION
MAY CREATE THE RISK OF ELECTROCUTION. USE OF SUCH
ADAPTERS IS NOT PERMITTED IN CANADA.
3. Where possible, avoid the use of extension cords. If they must
be used, minimize the risk of overheating by ensuring that they
are UL listed and of the proper gage and length. Never use a
single extension cord to operate more than one fan.
4. Do not insert fingers or foreign objects into the fan. Do not block
or tamper with the fan in any manner while it is in operation.
5. To avoid the possibility of overturning the fan, ensure that it is
operating on a stable, level surface.
6. Unplug power cord before installing or servicing the fan
7. Completely reassemble fan, according to instructions, before
reconnection to power supply.
WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH
AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
INSTALLING OR SERVICING THE FAN. ALWAYS UNPLUG
THE POWER CORD.
8. This fan is intended for general use ONLY. It must NOT be
used in potentially dangerous locations such as flammable,
explosive, chemical-laden or wet atmospheres. DO NOT use
fan in a window. Rain may create an electrical hazard.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT USE THIS FAN WITH ANY SOLID STATE
SPEED CONTROL DEVICE.
OPERATION
1. Plug the fan into any standard 120V AC household outlet.
2. Using the rotary switch, set the desired fan speed.
3. To rotate fan, loosen knobs on side of grill and tilt to direct
air flow.
MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING
OR SERVICING THE FAN.
CLEANING
1. Use a soft cloth moistened with a mild soap solution.
NEVER
IMMERSE ELECTRICAL PARTS IN WATER.
Avoid use of
gasoline, benzine, thinner, chlorinated solvents, harsh clean-
ers, etc. This will result in damge to the fan.
9" (22.9 cm) PIVOT FAN
MODEL 4CH69/9525
MODEL
4CH69/9525
SPEED
HIGH
LOW
CFM
1140
880
M
3
/s
.54
.42
RPM
2449
1883
Amps
.57
.39
Watts
37
27
dB A
48
37
Rev. B 8/00
1
2084014
MODELO 4CH69/9530
Rev. B 8/00
4
2084014
LUBRICACIÓN
Los cojinetes de precisión vienen sellados de fábrica de por vida y no
requieren de lubricación adicional.
ALMACENAMIENTO
Cuando no esté en uso, guarde la unidad en un lugar limpio y seco.
ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIOS O
DESCARGAS ELÉCTRICAS, NO USE ESTE VENTILADOR CON
NINGÚN DISPOSITIVO DE CONTROL DE VELOCIDAD DE ESTADO
SÓLIDO.
1
4
10
2
8
12
5
13
11
15
9
3
14
6
7
16
7
6
REF
NO.
NO. DE
PARTE
DESCRIPCIÓN
CANT.
1
208
Parrilla Delantera Plastico
1
2
2011851
Parrilla Tracera Plastico
1
3
2011852
Armadura De Plastico
1
4
2011853
Aspa De 9 Pulgagas
1
5
2091501
Abrazadera
1
6
2011854
Boton Adjustable
2
7
2011856
Arandela De Goma
2
8
2011721
Boton Interruptor
1
9
2010403A
Pies De Goma
4
10
2057062
Interruptor, 2 Velocidade
1
11
2060100
Placa Montadura
1
12
2050042WT
Cordon Electrico
1
13
2090039
Tornillo #8 x 3/8" PPH
4
14
3091112
Tuerca Tipo Hex #8-32
2
15
2030057
Ensamble Del Motor
1
16
2070024G
Ornamento (AirKing)
1
la cabeza del ventilador. Saque los botones y los aros interiores de
caucho. Tire suavemente de los extremos del yugo hasta que salgan
y saque los ejes roscados de los orficios del yugo. Agarre suavemente
la parte superior e inferior del ventilador. Presione lentamente sólo
hasta que las cubiertas se desmonten. Limpie las aspas del ventilador
con un paño humedecido. NO DEJE QUE EL AGUA ENTRE EN EL
MOTOR. Vuelva a instalar las rejillas tal como se habian montado
anteriormente invirtiendo el orden seguido para desmontarlas.
Asegúrese de que el ventilador esté completamente seco antes
de enchufarlo.
LISTA DE REPUESTOS
