background image

 

 

 

ONE - YEAR LIMITED WARRANTY 

Air Quality Engineering, Inc., warrants to the original purchaser, subject to the conditions below, that should 
the product covered by this warranty 

(“product”) fail to perform by reason of improper workmanship or 

material, Air Quality Engineering, Inc., (AQE) will, during the period of one (1) year from the date of original 
purchase either (i) replace the Product or (ii) provide all necessary parts to repair the Product, without 
charge. The decision to replace the Product or the necessary parts shall rest solely with AQE. This one-year 
limited warranty does not apply to main filter elements. Air Quality Engineering, Inc., will replace without 
charge the main filter elements during the period of thirty (30) days from the date of original purchase if the 
main filter elements fail to perform by reason of improper workmanship or material. This warranty is valid 
only under the following conditions:

 

 

CONDITIONS 

1.  AUTHORIZATION: Purchaser will contact Air Quality Engineering, Inc., 800-328-0787, for  authorization, 

returned goods authorization number (RGA) and shipping address. AQE will direct purchaser to either 
return the necessary parts or the Product at AQE’s option.

 

 

2.  PROPER DELIVERY: The shipping, freight prepaid, or delivery of the parts or the Product to Air Quality 

Engineering, Inc., in either its original carton or in a carton assuring similar protection of the Product 
with returned goods number (RGA) clearly displayed on the outside of the carton.

 

 

3.  UNAUTHORIZED REPAIR: A showing by the original purchaser that the Product has not been altered, 

repaired or serviced by anyone other than an authorized service technician using genuine AQE parts.

 

 

4.  UNAUTHORIZED PARTS: A showing by the original purchaser that the Product has had only genuine Air 

Quality Engineering, Inc., parts and filters used in its operation and maintenance.

 

 

5.  SERIAL NUMBER INTACT: A showing by the original purchaser that the Serial Number has not been 

altered or removed.

 

 

6.  MISUSE: A showing by the original purchaser that the Product has not been involved in an accident, 

freight damaged, misused, abused or operated contrary to the instructions contained in the 

Owner’s 

Manual.

 

 

Air Quality Engineering, 

Inc.’s, sole responsibility shall be to repair or replace the Product within the terms 

stated above. AQE shall not be liable for any consequential damages resulting from and breach of warranty, 
express or implied, applicable to the Product. Some states do not allow the exclusion or limitation of 
consequential damages so this limitation may not apply to you.

 

 

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE 
WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not

 

allow limitations on how long an implied warranty lasts so the above limitation may not apply to you.

 

 

This warranty gives you specific legal rights and you may also have other rights that vary from state to state.

 

 

 

MANUFACTURER & WORLDWIDE DISTRIBUTOR OF SMOKEMASTER® AIR CLEANING SYSTEMS

 

 

PN 51414 Rev. C 

Printed in the USA 

 
 

These air cleaners have not been tested for compliance to California Air Resource Board requirements and are not 
available for sale, resale or installation in California. 

CERTIFICATE OF WARRANTY

 

Page 14

S M O K E M A S T E R   C - 1 2   O W N E R ' S   M A N U A L 

Pure n Natural Systems, Inc.  |  purennatural.com  |  1-800-237-9199

Summary of Contents for SMOKEMASTER C-12















Reviews: