background image

LOGICOOL™ 

Chillers 

 

 

 

18 

 Chillers 

 Technical Manual : 6521355 V1.14.0 11/2016 

 

Performance Data 

 

 

 

ESEER CALCULATIONS 

The quoted EER figures (

General Specification

, on page 28) cover the performance of the 

unit ONLY at the standard rating conditions of 7/12°C water, 35°C ambient. The ESEER 
calculation method has been developed by Eurovent to give a single value that is a 
realistic indication of the efficiency of the chiller across the whole range of operation. 

 

The ESEER value is calculated from the unit’s performance at 20, 25, 30 and 35°C 
ambient temperatures for all loading stages, and with a fixed 7°C supply temperature. All 
calculations assume the system operates with 100% water. 

 

ESEER = A.EER

100% 

+ B.EER

75% 

+ C.EER

50% 

+ D.EER

25%

 

 

A, B, C and D are weighting factors 0.03, 0.33, 0.41 and 0.25. 

 

 

Temperature 

20°C 

25°C 

30°C 

35°C 

Capacity Requirement 

25% 

50% 

75% 

100% 

Percentage of Total Hours 

0.25 

0.41 

0.33 

0.03 

 
 

FSEER CALCULATIONS 
(Free Cooling) 

Whilst the ESEER is useful for providing a true energy efficiency of a unit’s performance 
over a year it does not offer any advantages for use of free-cooling which can significantly 
reduce the unit’s lifecycle power consumption.  

 

 

 

The FSEER calculation method has been developed by Airedale to give a single value 
that is a realistic indication of the efficiency of the chiller across the whole range 
of operation. 

 

 

 

 

The quoted Airedale FSEER figures (

General Specification

, on page 28) are similar to the 

ESEER and includes the unit’s free cooling capacity within the calculation. All calculations 
for the FSEER use water with 20% ethylene glycol content. Flow rates are kept constant 
for all conditions and are determined by the operation at 7/12°C, 35°C ambient. 

 

 

 

Free cooling capacity is included within the units EER when available. DX cooling 
capacity is included within the Chillers EER when the Free-cooling available is not 
sufficient to satisfy the total cooling demand. 

 

 

 

ESEER = A.EER

100% 

+ B.EER

75% 

+ C.EER

50% 

+ D.EER

25%

 

 

 

 

A, B, C and D are weighting factors 0.05, 0.25, 0.47, 0.23. 

 

 

Temperature 

0°C 

10°C 

20°C 

30°C 

Capacity Requirement 

0.25 

0.5 

0.75 

Percentage of Total Hours 

0.23 

0.47 

0.25 

0.05 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for LogiCool LCC20







































Reviews: