background image

AirVerter

® 

Model 96 HVLP Paint Spray System

DO NOT OPERATE SPRAY GUNS WITHOUT PERSONAL SAFETY EQUIPMENT

2

Please Read This Owner’s Manual BEFORE

Using Your Model 96 Spray Gun

DO NOT OPERATE THIS EQUIPMENT WITHOUT USING PROPER PERSONAL
SAFETY EQUIPMENT INCLUDING RESPIRATOR, GOGGLES AND SAFETY
CLOTHING. OBSERVE ALL PRECAUTIONS RELATED TO SPRAYING.

WARNING

THIS EQUIPMENT IS OPERATED USING PRESSURIZED AIR.  ALWAYS
DISCONNECT SPRAY GUN FROM AIR AND FLUID HOSES AND
DEPRESSURIZE SYSTEM PRIOR TO ANY MAINTENANCE OR DISASSEMBLY
PROCEDURE.

WARRANTY

Smith Eastern Corporation warrants to the Purchaser that the Model 96 HVLP Spray Gun is free from
defects in material or workmanship under normal use and service for a period of twelve (12) months from
the date of receipt by the Purchaser.  Should any failure appear during this period, Smith Eastern shall, if
given prompt written notice by the Purchaser, correct such nonconformity by repair or replacement of the
nonconforming part, F.O.B. Smith Eastern’s repair facility.  Repair parts are warranted for ninety (90)
days from the date of shipment, but repairs or replacements to original equipment shall not renew or
extend the warranty period of such equipment.

Smith Eastern reserves the right to limit this warranty in cases of misuse or abuse.  Any modifications to
spray guns or recommended procedures will void the warranty.

The foregoing warranty is exclusive and in lieu of other warranties of quality or performance, expressed,
implied or statutory, including any warranties of merchantability or of fitness for a particular purpose.

Why AirVerter

®

 Spray Gun Systems Work Better

To accomplish effective atomization of a liquid at low pressure (below 10 PSI) it is necessary to
substantially increase the air volume (CFM).  The AirVerter

®

 Inductor, a patented system, converts high-

pressure compressed air to low pressure air (10 PSI or below) and increases air volume substantially.
The result is less overspray and greater transfer efficiency.

AirVerter

®

 systems, by design, do not exceed 10 PSI at the spray head and prevent the operator from

taking AirVerter

®

 spray guns out of compliance with EPA and California’s South Coast Air Quality

Management District (SCAQMD) regulations.

Summary of Contents for AV-096













Reviews: