Aiwa XR-DV826, Service Manual

– 38 –

< TUNER  SECTION >

1. Clock frequency Check

Settings : • Test point : TP2 (CLK)
Method : Set  to MW 1602kHz and check that the test point is

2052kHz 

±

 45Hz.

2. MW VT Adjustment

Settings : • Test point : TP1 (VT)

• Adjustment location : L953

Method : Set to MW 1710kHz and adjust L953 so that the test

point becomes 8.5V 

±

 0.05V. Then set to MW 530kHz

and check that the test point is more than 0.3V.

3. MW Tracking Adjustment

Settings : • Test point : TP5(Lch), TP6(Rch)

• Adjustment location :
L952 ................................................ 603kHz
TC941 ........................................... 1404kHz

Method : Set up TC941 to center before adjustment.

The level at 603kHz is adjust to max. by L952.
Then the level at 1404kHz is adjust to max. by TC941.

4. AM IF Adjustment

Settings : • Test point : TP5(Lch), TP6(Rch)

• Adjustment location :
L802 ................................................ 450kHz

5. SW VT Adjustment

Settings : • Test point : TP1(VT)

• Adjustment location : L942

Method : Set to SW 17.9MHz and adjust L942 so that the test

point becomes 8.0V 

±

 0.05V. Then set to SW 5.73MHz

and check that the test point is more than 0.3V.

6. SW Tracking Adjustment

Settings : • Test point : TP5(Lch), TP6(Rch)

• Adjustment location :
L941 ............................................. 5.73MHz
TC943 .......................................... 17.9MHz

Method : Set up TC943 to center before adjustment.

The level at 5.73MHz is adjust to max. by L941.
Then the level at 17.9MHz is adjust to max. by TC943.

7. FM VT Check

Settings : • Test point : TP1 (VT)
Method : Set to FM 87.5MHz, 108.0MHz and check that the test

point is more than 0.5V (87.5MHz) and less than 8.0V
(108.0MHz).

8. FM Tracking Check

Settings : • Test point :  TP5(Lch), TP6(Rch)
Method : Set to FM 98.0MHz and check that the test point is

less than 9dB

µ

V.

9. DC Balance / Mono Distortion Adjustment

Settings : • Test point :  TP3, TP4 (DC Balance)

                  : TP5(Lch), TP6(Rch) (Distortion)

• Adjustment location : L801
• Input level : 60dB

µ

V

Method :

Set to FM 98.0MHz and adjust L801 so that the
voltage between TP3 and TP4 is 50mV 

±

 300mV with

minimum distortion.

ADJUSTMENT  <TUNER / DECK / FRONT>

< DECK  SECTION >

10. Tape Speed Adjustment (DECK 2)

Settings : • Test tape : TTA–100

• Test point : TP9(Lch), TP10(Rch)
• Adjustment location : SFR1

Method : Play back the test tape and adjust SFR1 so that the

frequency counter reads 3000Hz 

±

 5Hz (FWD) and

±

 45Hz (REV) with respect to forward speed.

11. Head Azimuth Adjustment (DECK 1, DECK 2)

Settings : • Test tape : TTA–300

• Test point : TP9(Lch), TP10(Rch)
• Adjustment location : Head azimuth

adjustment screw

Method : Play back (FWD) the 10kHz signal of the test tape

and adjust screw so that the output becomes maximum.
Next, perform on REV PLAY mode.

12. PB Frequency Response Check (DECK 1, DECK 2)

Settings : • Test tape : TTA–330

• Test point :TP9(Lch), TP10(Rch)

Method : Play back the 315Hz and 10kHz signals of the test tape

and check that the output ratio of the 10kHz signal with
respect to that of the 315Hz signal is 0dB 

±

 3dB.

13. PB Sensitivity Check (DECK 1, DECK 2)

Settings : • Test tape : TTA–200

• Test point : TP9(Lch), TP10(Rch)

Method : Play back the test tape and check that the output level of

the test point is 280mV 

±

 3dB.

14. REC/PB Frequency Response Adjustment (DECK 2)

Settings : • Test tape : TTA–602

• Test point : TP9(Lch), TP10(Rch)
• Input signal : 1kHz / 10kHz (LINE IN)
• Adjustment location : SFR351 (Lch)

SFR352 (Rch)

Method : Apply a 1kHz signal and REC mode. Then adjust

OSC attenuator so that the output level at the TP7,
TP8 becomes 28mV. Record and play back the 1kHz
and 10kHz signals and adjust SFRs so that the output of
the 10kHz signals becomes 0dB 

±

 1.0dB with respect to

that of the 1kHz signal.

15. REC/PB Sensitivity Check (DECK 2)

Settings : • Test tape : TTA–602

• Test point : TP9(Lch), TP10(Rch)
• Input signal : 1kHz (LINE IN)

Method : Apply a 1kHz signal and REC mode. Then adjust

OSC attenuator so that the output level at TP7, TP8
becomes 280mV. Record and play back the 1kHz
signals and check that the output is –1dB 

±

 2.5dB.

< FRONT  SECTION >

1.

µ

-CON OSC Adjustment

Settings : • Test point : TP7 and TP8(GND)

• Adjustment location : L101

Method : Insert AC plug while pressing TUNER function key.

Adjust L101 so that the frequency at the test point is
208.80Hz 

±

 0.2Hz.