background image

9

En

Programmed play

Plays back up to 30 selected tracks in programmed order.

Hold down SHIFT and press PROGRAM on the

remote control in stop mode.

"

PRGM

" flashes on the display.

Press the numbered buttons on the remote

control to program a track.

-To select the 25th track, press +10, +10 and 5.
-To select the 11th track, press +10 and 1.
The selected track number lights up on the display.

Repeat step 2 to program other tracks.

The total number of selected tracks and total playing time
will be displayed.

Press 

E

 to start play.

The track number for the current track flashes on the
display.

•During programmed play, you cannot select a track with the

numbered buttons. "

CAN’T USE

" is displayed when you

try to select a track .

•If the total playing time of the program exceeds 99 minutes

and 59 seconds, or if a track with a track number exceeding
30 is programmed, the playing time is displayed as
"

- -:- -

".

•You cannot program more than 30 tracks. "

FULL

" is

displayed.

To check the program

Press 

f

  or 

g

  repeatedly in stop mode. The track

number and program number are displayed in succession.

To clear the program

Press 

s

 in stop mode. "

PRGM

" disappears from the display.

To add tracks to the program

Repeat step 2 before starting playback. The tracks are added
to the end of the program.

To change the programmed tracks

Clear the program and repeat all the steps again.

Notes on CDs

•Do not place more than one disc.
•Do not tilt the unit with a disc loaded.
•The unit may not play CD-R/RW discs recorded on personal

computers or certain kinds of CD-R/RW recorders.

•Do not attach adhesive label to either side of

CD-R/RW discs, as doing so may cause malfunction.

•Do not load an unrecorded CD-R/RW disc. The disc may be

damaged.

•Do not use irregular-shaped CDs.

Summary of Contents for XR-EM20





















Reviews: