manualshive.com logo in svg

AJA FS2, Installation & Operating Manual

Looking for a comprehensive User Manual for Mission FS2? Look no further! Download the free manual from 88.208.23.73:8080 and unlock the full potential of your Mission FS2. Discover step-by-step instructions, troubleshooting tips, and more, allowing you to maximize your product experience effortlessly.

Share
Download
background image

FS2 v2.1r1

www.aja.com

6

 

Region of Interest (ROI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   72

14.0 Region of Interest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   72
14.1 ROI Left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   72
14.2 ROI Right  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   72
14.3 ROI Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   72
14.4 ROI Bottom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   72

Timing and Delay  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   73

15.1 Output Timing H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   73
15.2 Output Timing V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   73
15.4 Extra Frame Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   73

Video Legalizer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   73

16.0 Video Legalizer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   73
16.1 Legalizer White Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   73
16.2 Legalizer Black Clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   74
16.3 Legalizer Chroma Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   74

AFD  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   74

17.1 AFD Out SDI 1/2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   74
17.2 AFD VANC Output Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   75
17.3 Downcvt AFD Dflt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   75

Closed Captioning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   75

18 Caption Xlator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   75

Input Scan and PSF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   76

19 Input Scan Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   76

SD Line 21Closed Caption Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   76

20 SD Line 21 Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   76

Test Pattern. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   77

21 Test Pattern Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   77

Freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   77

22 Freeze Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77

AUDIO 1 and AUDIO 2 Menu Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   77

1.0 Audio Input  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   78
1.1–1.16 Audio Map Ch1–16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   79
1.17–1.24 Audio Map Ch 1/2–15/16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   80
2 Embedded Audio Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  80
3 Audio Follow Video  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   80
4 Audio Signal Gen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   81
Audio Delay Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   81

6.0 Audio Delay (mS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   81
6.1-16 Audio Delay Ch1-16 (mS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   82
6.17-24 Audio Delay Ch1/2-15/16(mS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   82

Audio Output Level Controls  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82

7.0 Audio Out Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   82
7.1–7.16 Audio Level Ch1–16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   83

Audio Output Phase Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   83

8.0 Audio Output Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   83
8.1–8.16 Audio Phase Ch1–16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   83

Dolby Framer Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   83

9.0 Dolby Framer Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   83
9.1 Dolby Framer Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   84
9.2 Dolby Framer Offset (Frames) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   84
9.3 Dolby Framer Offset (Samples). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   84

Chapter 5: Browser Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

USO 

RESTRITO

Summary of Contents for FS2






























































































































Reviews:

No comments

Related manuals for FS2

ABB ACS 600 Startup Manual preview
ACS 600
Brand: ABB Pages: 10
IAdea XMP-300 User Manual preview
XMP-300
Brand: IAdea Pages: 16
I-Tech EMP100 User Manual preview
EMP100
Brand: I-Tech Pages: 14
iConnectivity iConnectMIDI Quick Start Manual preview
iConnectMIDI
Brand: iConnectivity Pages: 21
Kaco blueplanet 3.0 TL3 M2 WM OD IIG0 Operating Instructions Manual preview
blueplanet 3.0 TL3 M2 WM OD IIG0
Brand: Kaco Pages: 262
Lampizator Fezz Equinox EVO User Manual preview
Fezz Equinox EVO
Brand: Lampizator Pages: 5
X2E Automotive Ethernet Converter User Manual preview
Automotive Ethernet Converter
Brand: X2E Pages: 22
Nightlife SINGLE AUDIO Installation And Testing preview
SINGLE AUDIO
Brand: Nightlife Pages: 12
A-TS TECHNOLOGY DT100-2S0004G User Manual preview
DT100-2S0004G
Brand: A-TS TECHNOLOGY Pages: 131
CyberPower CPS150BURC1 User Manual preview
CPS150BURC1
Brand: CyberPower Pages: 1
Brunner 0826089N Quick Start Manual preview
0826089N
Brand: Brunner Pages: 8
MRC 0001819 Quick Start Manual preview
0001819
Brand: MRC Pages: 2
GPX MW350B User Manual preview
MW350B
Brand: GPX Pages: 2
Tecsun H-501x Quick Start preview
H-501x
Brand: Tecsun Pages: 2
Directed Electronics DMP040 Installation Manual preview
DMP040
Brand: Directed Electronics Pages: 58
PhD Solutions CON-OC-A192 Operation Manual preview
CON-OC-A192
Brand: PhD Solutions Pages: 14
Dvico TViX HD M-4000P User Manual preview
TViX HD M-4000P
Brand: Dvico Pages: 59
KD IT 01579400217 Manual preview
IT 01579400217
Brand: KD Pages: 26

Brands by name

Popular brands

Load more brands