background image

OG-ROI Series openGear card v1.6 15 www.aja.com

 

A third example (

Figure 13

) illustrates use of the OG-ROI Rotation feature to 

send selected areas of a SDI signal to portrait mounted on-set monitors at full 

resolution. Each monitor uses one OG-ROI converter, accomplishing the task at a 

much lower cost than dedicating DVE channels for rotation and resizing. 

Figure 13.  OG-ROI Rotation with Portrait Mounted On-Set Monitors

OG-ROI B

Ethernet 

HDMI Output

HDMI Output

OG-ROI A

Portrait

SDI Monitors

Built Into Set

Region

A

Region

B

HDMI/DVI 

Loop-Through

- Input ROI Selection: 9x16 Fixed Aspect 

- Output ROI Out Scaling: Full Screen Rotated 90 Degrees

SDI converted to 
HDMI/DVI

Digital Video

Camera

Computer

w/ DashBoard

A fourth example below illustrates sending HDMI digital video from a camera to 

an OG-ROI to allow region of interest video input to a video switcher. 

Figure 14.  OG-ROI-HDMI with Video Camera to Switcher Interconnect 

Diagram

OG-ROI

HDMI

Ethernet

SDI

Output

Computer

w/ DashBoard

Video Switcher

Digital Video

Camera

Computer Desktop

Monitor

(ROI Pass-through)

SDI converted to 
HDMI/DVI

In a parallel configuration as 

Figure 14Figure 15 

below shows a basic 

configuration of the OG-ROI being used to send a 3G-SDI digital video signal 

from a 3G-HDMI or 3G-DVI source to allow region of interest video input to a 

video switcher. You can use methods for adjusting the region of interest selection 

described in the section for th

"Input Screen" on page 19 

with the processed 

3G-SDI output signal feeding a monitor.

Summary of Contents for OG-ROI Series
















































Reviews: