LOCK:
When the mixer's crossfader is moved to the end belonging to
the channel of the player every time, the playback will start and
then pause instantly.
TACT:
When the mixer's crossfader is moved to the end belonging to
the channel of the player for the first time, the playback will
start.
When the mixer's crossfader is moved to the end belonging to
the channel of the player again, the playback will pause.
CUE/PLAY:
When the mixer's crossfader is moved toward the channel of the
player, the playback will be started from the last Main CUE.
With this button you can adjust the touch Sensitive too.
Holding this button and switching on the power will lead into the
mode for adjusting the sensitivity of Touch Wheel. Float your
hand very close to the jog wheel. It will detect the sensitive
value. It has to increase 2 degree from the value detected. Press
SKIP to reach the value and press MEMO to save the value and
reboot for returning to normal use.
* This adjustment only needs when finding the sensitivity
difference in a specific environment.
More info about remote control on General Functions Overview
(Page 17).
(Page
17).
Note: Not recommended to manipulate the sensitivity setting if
not for failure.
6. TITLE/LIST
Press this button to show FILE, TITLE, ALBUM and ARTIST.
When the unit is under pause, pressing this button during 2
seconds can enter into play lists selecting. It shows the four play
modes: M3U, XML, WPL, and normal Folder. Holding TITLE/LIST
press
FOLDER/TRACK
to switch between these four
modes. Once you decide the format you want to play (assume
you have stopped at XML), release TITLE/LIST button. It will lead
to the all play-lists in this kind of format. If you want to exit this
play list, press and hold LIST button and then one press
FOLDER/TRACK
*NOTE: It supports MP3 format only.
More info at GENERAL FUNCTIONS OVERVIEW page 17.
7. HOT-CUE
XCEED will allow you to play from 3 cue points instantly.
A. Set CUE memory: Press MEMO first and then press a certain
CUE button to finish the CUE record. The set CUE button will
light on.
B. Play” CUE” memory: Press the set CUE button to perform this
function.
*Hold MEMO and dial the jog wheel to preset the beat length of
Auto Loop. This means it's ready to execute the auto loop
playback. Pressing IN will auto form an auto loop according the
beat to length you set.
The bar range of auto loop can be selected from 1/32~32/1.
More info about autoloop on General Functions Overvi
8. LOOP
a. Press IN to memorize a start point and press OUT to
memorize an end point. Then the Loop starts playing.
b. Press OUT again to edit the Loop playback. The length of the
Loop playback can be enlarged or shortened by turning jog
wheel.
c. Press the RELOOP to exit or call the Loop playback.
d. The loop function will be limited at the same track for MP3. It
can't set the IN at track 1 and cross to set the OUT at track 2.
On the contrary, it can be set a loop crossing between track to
track for CDDA.
9. RELAY
NOTE: You will need two EXCEED units interconnected through
RELAY connector.
Press the “RELAY” button to activate this function. When one unit
is in play mode, and the other unit is in “pause” mode. Then,
pause the playing unit and the other unit will automatically start
to play.
*This button is also for switching between the gain and the
parameter of the digital effect showing in the display.
10.
FOLDER/TRACK
10.1. To select a track, a folder or a partition. Hold it and dial the
jog wheel to do tracks fast search.
10.2. When a loop is formed, pressing
will trim the loop
double and pressing
will trim the loop to half.
*It can't skip the track during the loop playback.
EDIT A LOOP
ew
Touch Sensitive Adjustment
CONT.
HOLD
1
XCEED OFF
+
SWITCH XCEED ON
2
LOOP TRIM
CUT
EXTN
FOLDER
TRACK
Float yout hand over wheel top and check the
bar movement indicating touch wheel
response.
Press buttons to increase of diminish
sensibility.
Sensibility
UP
DOWN
3
Press MEMO to save the value and reboot for
retuning to normal use.
LOOP EDIT
OUT
wheel
LENGTHEN LOOP
SHORTEN LOOP
HOLD
LOOP EDIT TIME INFO >
DISPLAY
1
SET LOOP
2
PRESS & HOLD OUT, TURN WHEEL TO EDIT
Xceed user manual. Description of the functions. Top view.
14
