background image

User’s Manual

AMM-1032

True RMS   

AUTORANGING MULTIMETER 

                     

 

SAFETY INFORMATION 

 

The following safety information must be observed to 
insure maximum personal safety during the operation 
at this meter: 
 

 

Do  not  use  the  meter  if  the  meter  or  test  leads 
look damaged, or if you suspect that the meter is 
not operating properly. 

 

Never  ground  yourself  when  taking  electrical 
measurements. Do not touch exposed metal pipes, 
outlets,  fixtures,  etc.,  which  might  be  at  ground 
potential.  Keep your  body isolated  from  ground 
by using dry clothing, rubber shoes, rubber mats, 
or any approved insulating material. 

 

Turn  off  power  to  the  circuit  under  test  before 
cutting,  unsoldering,  or  breaking  the  circuit. 
Small amounts of current can be dangerous. 

 

Use caution when working above 60V dc or 30V 
ac rms. such voltages pose a shock hazard. 

 

When using the probes, keep your fingers behind 
the finger guards on the probes. 

 

Measuring  voltage  which  exceeds  the  limits  of 
the  multimeter  may  damage  the  meter  and 
expose  the  operator  to  a  shock  hazard.  Always 
recognize  the  meter  voltage  limits  as  stated  on 
the front of the meter. 

 

 

Never apply voltage or current to the meter that 
exceeds the specified maximum: 

 
 
 

SAFETY SYMBOLS 

 

This  symbol  adjacent  to  another 
symbol,  terminal  or  operating  device 
indicates  that  the  operator  must  refer 
to  an  explanation  in  the  Operating 
Instructions  to  avoid  personal  injury 
or damage to the meter. 

This 

WARNING

  symbol  indicates  a 

potentially  hazardous  situation,  which 
if not avoided, could result in death or 
serious injury. 

This 

CAUTION

  symbol  indicates  a 

potentially  hazardous  situation,  which 
if  not  avoided,  may  result  damage  to 
the product. 

This  symbol  advises  the  user  that  the 
terminal(s)  so  marked  must  not  be 
connected  to  a  circuit  point  at  which 
the  voltage  with  respect  to  earth 
ground exceeds (in this case) 500 VAC 

Input Limits 

Function 

Maximum Input 

V DC or V AC 

1000VDC/VAC 

A DC/AC 

10A  DC/AC  (30 

seconds max every 

15 minutes) 

Frequency, 

Resistance, 

Capacitance,  Cycle, 

Diode 

test, 

Continuity 

600V DC/AC 

Temperature 

600V DC/AC 

WARNING

CAUTION

MAX 

http://www.tmatlantic.com

Summary of Contents for AMM-1032








Reviews: