background image

Specifications

Power Supply : 230V ~ 50Hz
Power Consumption : 13 Watt
Output Power(RMS) : 2 x 2W
Terminal impedence : Speaker 4ohms
Main Unit Dimensions : 220(L) x 150(W) x 165(H)mm

Net Weight : 3.3kg
Gross Weight : 4kg
Tuning Frequency : AM: 540-1600 KHz
 

                FM: 88-108 MHz

Fault Guide.

Symptom

Fault

Action

No power to player. 

Check the power plug is in 
firmly and connected to a 
power supply.
If batteries are fitted, ensure 
they are new and fitted the 
correct way round. 

Dead. No Operations

Function switch in incorrect
position.

Switch to CD or Radio

No Radio operations but Led
lit

Function switch set to CD 

Switch to Radio. Turn up the 
volume.

No Radio stations on MW 

Poor signal area

Rotate the case of the radio as 
the internal aerial is 
directional. The extending rod 
aerial is not in use on AM 

No Radio stations on FM 

Poor signal area

Extend and rotate the rod 
aerial.

Dirty or damaged disc

Carefully clean the disc and
place in the player label side
up.

Not playing CD’s

Dirty laser lens

Carefully clean the lens with a 
“cotton bud”.

Page 8

Should you experience any problems please see guide below before calling the help line

Speaker Dimensions : 150(L) x 150(W) x 165(H)mm

If you are still having difficulty please call the Technical help line. Ring 01422 263313 (Normal rates 
apply).
Opening hours Mon-Fri 8 am – 8pm. Sat 9 am – 4pm. Sun 11am – 4pm “Bank holidays as Sun”
Or try our website :- www.ekey.co.uk (24Hr)

Summary of Contents for APTMIC110AR











Reviews: