background image

     © 2016 AKW  

                                                             

  

 15-010-048-01

Orderline 

+44 (0) 1905 823299

General Enquiries

+44 (0) 1905 823298

Technical Help line

+44 (0) 1905 560219

 

Fax

+44 (0) 1905 823297

Website

www.akw-ltd.co.uk

Quotes & orders email

orders@akw-ltd.co.uk

Enquiries email

sales@akw-ltd.co.uk

technicalenquiries@akw-ltd.co.uk

 

Postal address

 

AKW, Pointon Way,  

 Hampton Lovett,      

 Droitwich Spa,  

 WR9 0LR

What to do if something goes wrong?

In the unlikely event that you should

encounter a problem with this product,

please contact your local installer and

if this does not resolve the issue then

contact AKW technical team who will

provide further advice and if necessary

arrange for a maintenance engineers to 

visit and report any issues. 

As part of our quality and training 

programme calls may be monitored or 

recorded. None of the foregoing affects 

your statutory rights.

These instructions are provided to advise the minimum standards of installation and recommends what is the best practice for the installation. 

Due to the very wide variability of possible installation conditions AKW cannot provide all circumstances for the installation. AKW cannot accept any 

liability in connection with this information or its use. This information is provided on the condition that the person receiving it shall make their own 

tests to determine the suitability for their particular purpose. Failure to install this AKW product in accordance with supplied instructions or the 

making of unauthorised modifications will invalidate any warranty and may affect product safety. 

None of the foregoing affects your statutory rights.

Warranty information

Glass Screens are covered by a life time guarantee. 

* The guarantee applies only to manufacturing or  

material defects and does not apply to:

•  Normal wear and tear, inappropriate use or 

•  accidental damage.

•  Damage or defects that result from incorrect 

installation, improper use, accidental damage 

or lack of maintenance including the build up 

of grime, dirt or lime-scale and water-borne 

debris.

•  Damage resulting from inappropriate cleaning 

or water ingress. 

•  Damage or defects that result from repairs, 

modifications undertaken by unauthorised persons 

who are not installers or service engineers. 

AKW products should be installed by an experienced 

and competent installer or trades persons using 

appropriate fixings suitable for the condition of the 

surfaces on which the product is to be attached. 

The selection of any specific fixings must be made by 

the installer based upon the requirements for each 

individual installation.
If you do not install AKW product in accordance 

with the supplied instructions or if you carry out 

any unauthorised modifications to this product then 

you will affect product safety and invalidate this 

guarantee.

For further information latest AKW 

product news please visit our website 

or scan this QR code with your device. 

Guaranteed 

for         

*

Life

Summary of Contents for Level Best

















Reviews: