469861_c
43
Transport
Malfunction
Cause
Remedy
Motor does not run.
No battery voltage present.
Have the power supply checked by
a qualified electrician.
Overload protection has
switched off.
Wart until the overload protection re-
establishes the power supply.
Chain brake engaged.
Release the chain brake.
The guide rail and saw chain
become hot when running.
Generation of smoke.
The saw chain is tensioned
too tightly.
Reduce chain tension.
Oil tank is empty.
Replenish the saw chain oil.
Inspect the oil tank for damage.
The oil entry hole and/or
groove of the guide rail are
dirty.
Clean the oil entry hole and groove
of the guide rail.
Engine running, but the saw
chain does not move.
The saw chain is tensioned
too tightly.
Reduce chain tension.
Device errors
Contact an AL-KO service centre.
Only sawdust is thrown out,
rather than wood chips. The
chain saw has to be pushed
through the wood.
The saw chain is blunt.
Sharpen the saw chain or contact an
AL-KO service centre.
Device vibrates unusually.
Device errors
Contact an AL-KO service centre.
17 TRANSPORT
WARNING! Danger of fatal injury and
danger of extremely severe injury.
During
transport, a running saw chain can lead to ex-
tremely serious and even fatal injury.
■
Never carry and transport the chain saw with
the saw chain running.
■
Before transporting, carry out the measures
mentioned above.
Before transporting, carry out the following mea-
sures:
1. Switch off the chain saw and remove the re-
chargeable battery.
2. Fit the chain guard.
3. Carry the chain saw only at the bow handle.
Guide rail and saw chain should be facing to
the rear.
4. In vehicles: Secure the chain saw against tip-
ping over, damage and leakage of chain oil.
18 STORAGE
Thoroughly clean the chain saw after each use.
Store it in a dry, lockable place out of the reach of
children.
Carry out the following jobs before intervals in
work lasting for longer than 30 days:
■
Switch off the chain saw and remove the re-
chargeable battery.
■
Empty the oil tank for the saw chain oil.
■
Remove the saw chain and guide rail, clean it
and spray it with rust-proofing oil.
■
Thoroughly clean the chain saw and store it
in a dry place.
IMPORTANT! Danger of damage to the ap-
pliance.
Dried/sticky saw chain oil can lead to
damage to oil-channelling components or the oil
pump after lengthy storage.
■
Remove the saw chain oil from the chain saw
before each extended period of storage.
19 DISPOSAL
Information on the German Electrical and
Electronic Equipment Act (ElectroG)
■
Electrical and electronic appliances do
not belong in household waste, but
should be collected and disposed of
separately.
Summary of Contents for CS 4030
