Assembly
440565_b
17
ASSEMBLY
CAUTION!
Danger of injury if the machine is incom-
plete!
Incomplete machines can lead to injuries
and damage to the machine!
Do not operate the machine unless it has
been fully assembled.
Scope of supply
Carefully remove the shredder from its packaging
and check the following parts for completeness:
Base with grass catcher
Two transport wheels with wheel caps
Upper shredder part with cutting and motor
unit
Hopper
Assembly bag with screws and tools, instruc-
tions for use with warranty card and service
station listing.
Mounting the transport wheels
1. Slide the wheel axle (2/1) into the base (2/2).
2. Next, slide a large 10x20x1.5 washer (2/3)
and the bushing (2/4) onto axle (2/1).
3. Afterwards, slide the transport wheel (2/5)
onto the bushing (2/4).
4. Slide the medium 8x20x1.5 washer (2/6) onto
the thread and secure the transport used a M8
nut (2/7).
5. Finally, press the wheel cap (2/8) onto the
transport wheel (2/5).
6. Assembly of all opposite transport wheel ta-
kes place in the same sequence.
Assembling the upper shredder part with
cutting and motor unit (3)
1. Lift the upper shredder part onto the base and
secure it using M5x30 screws (3/1) and was-
hers 5x10x1.
Assembling the hopper (3)
1. Place the hopper onto the upper shredder part
and secure it using ST 4.2x18 screws (3/2).
STARTUP
Comply with working time regulations in force
in your country.
The extension cable must not cross over hop-
per or ejector.
The shredder can only be started when the
grass catcher is locked.
Check hopper and upper shredder part for
obstructions prior to starting the machine.
Do not use the shredder if you are:
Tired
Unwell
Under the influence of alcohol, medici-
nes and drugs
DANGER!
Danger of injury from damaged compo-
nents!
Damaged components can lead to se-
rious and even fatal injuries!
Before taking into operation, carry out a
visual inspection and check the compo-
nents for function.
WARNING!
Risk of injury due to negligence!
Negligence in handling the machine can
result in serious injuries!
Only use the shredder on firm, level
ground and in a stable setup. Do not tilt
or incline the machine during operation.
OPERATION
Operating time
The machine design supports the S6 (40 %) ope-
rating time. This means that the shredder may be
used 60 % in idle and 40 % under load. For a
time unit of 10 minutes this means 6 minutes idling
and 4 minutes under load. Continuous operation
is possible under these conditions.
Connecting the mains plug
1. Push down the cable safety (4/1) and insert
the extension cable (5/1) into the socket of the
shredder.
2. Check secure fit of the extension cable.
3. Next, connect the extension cable to your
mains voltage.
Switching on the motor
1. Press the On-switch (6/1).
Switching off the motor
1. Press the Off-switch (6/2) to switch the motor
off.
Summary of Contents for Easy Crush MH 2800
