AL-KO EKI 2200/40 Instructions For Use Manual Download

Page: 36 / 412

EKS 2000/35 | EKS 2400/40 | EKI 2200/40

Safety instructions

Kickback is the result of tool misuse and/or incor-
rect operating procedures or conditions and can
be avoided by taking proper precautions as given
below:

■

Maintain a firm grip, with thumbs and fin-
gers encircling the chain saw handles,
with both hands on the saw and position
your body and arm to allow you to resist
kickback forces.

Kickback forces can be

controlled by the operator, if proper precau-
tions are taken. Do not let go of the chain
saw.

■

Do not overreach and do not cut above
shoulder height.

This helps prevent unin-

tended tip contact and enables better control
of the chain saw in unexpected situations.

■

Only use replacement bars and chains
specified by the manufacturer.

Incorrect re-

placement bars and chains may cause chain
breakage and/or kickback.

■

Follow the manufacturer’s sharpening and
maintenance instructions for the saw
chain.

Decreasing the depth gauge height

can lead to increased kickback.

3.1.8

Vibration load

■

Danger due to vibration

The actual magnitude of the vibration emis-
sions during the use of the appliance may de-
viate from that stated by the manufacturer.

Observe the following influencing factors be-
fore or during use:

■

Is the appliance being used as intended?

■

Is the material being cut or processed in
the proper manner?

■

Is the appliance in a proper condition of
use?

■

Is the cutting tool properly sharpened or
is the correct cutting tool installed?

■

Are the handle grips and any optional vi-
bration grips mounted, and are they firm-
ly attached to the appliance?

■

Only operate the tool at the motor speed re-
quired for the respective work. Avoid using
the maximum speed in order to reduce noise
and vibrations.

■

The noise and vibrations of the tool may in-
crease due to improper use and mainte-
nance. This leads to health damage. In this
case, immediately switch off the tool and
have it repaired by an authorised service
workshop.

■

The degree of stress due to vibration de-
pends on the work to be performed or on the
use of the tool. Estimate the stress and plan
appropriate work breaks. This considerably
reduces stress due to vibration over the en-
tire working time.

■

Extensive use of the tool exposes the opera-
tor to vibrations, which can lead to circulatory
issues ("white fingers"). To avoid this risk,
wear gloves and keep your hands warm. If
any symptoms of "white fingers" occur, im-
mediately consult a physician. These symp-
toms include: Numbness, loss of feeling, tin-
gling, itching, pain, reduced muscular
strength, changes in the colour or condition
of the skin. Normally these conditions affect
the fingers, hands or pulse. The risk increas-
es at low temperatures.

■

Take long breaks during your working day so
you can recover from the noise and the vibra-
tions. Plan your work in such a way that the
use of appliances that generate strong vibra-
tions is spread over several days.

■

If you notice an unpleasant sensation or disc-
olouration of the skin on your hands when us-
ing the tool, stop work immediately. Take suf-
ficient work breaks. Without sufficient breaks,
a hand/arm vibration syndrome can occur.

■

Minimise your risk of being exposed to vibra-
tions. Maintain the tool according to the in-
structions in the operating instructions.

■

If the tool is used frequently, contact your
dealer to purchase anti-vibration accessories
(e.g. handles).

■

Avoid working with the tool at temperatures
below 10 °C. Define how the vibration load
can be limited in a work plan.

3.1.9

Noise pollution

A certain level of noise exposure from this appli-
ance is inevitable. Carry out noisy work at ap-
proved and specified time periods. Observe rest
periods as necessary and restrict the duration of
the work to a minimum. For your personal protec-
tion and protection of persons in the vicinity, ap-
propriate hearing protection must be worn.

3.2

Safety information when working

■

Heed the country-specific safety regulations,
e.g. from the relevant trade associations, so-
cial security systems, authorities for industrial
safety.

■

Only work in sufficient daylight or artificial
lighting.