Alarm Lock DL6100 Programming Instructions Manual Download | Manualshive

Page: 13 / 36

background image

13

Verifying Basic Keypad User Codes

Test a valid User Code:

VALID CODE -

The Green LED will flash momentarily and the sounder will beep a few times after a valid code is entered.

INVALID CODE -

The RED LED will flash several times and the sounder will beep several times after an invalid code is entered.

Use Function 2 to re-program the code.

Testing the Codes Entered

NOTES

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

____________________________________________________________________________________________

«
...
11
12
13
14
15
...
»

Summary of Contents for DL6100





































Reviews:

No comments

Related manuals for DL6100

Brand: Kaba Pages: 2

Brand: Kaba Pages: 37

Brand: Kaba Mas Pages: 2

Brand: Kaba Pages: 10

C-lever compact

Brand: Kaba Pages: 2

Brand: Kaba Pages: 28

Simplex 7104 Series

Brand: Kaba Pages: 4

Brand: M-LOCKS Pages: 16

Brand: 2gig Technologies Pages: 2

Brand: eKey Pages: 2

Brand: Kwikset Pages: 4

Smart Mortise 2

Brand: Igloohome Pages: 27

Brand: Stanley Pages: 2

Brand: Stanley Pages: 99

Combilocks COMBI-PUBLIC

Brand: MERONI Pages: 2

Brand: Kaba Pages: 10

Brand: Kaba Pages: 35

Brand: Kaba Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands