34
ACCESS
= Entry into a restricted area.
AUDIT TRAIL
= A date/time stamped log of previous
lock events.
CLOCK
•
REAL TIME
CLOCK
= An accurate built-in clock
that allows date/time stamping of events. The
clock can be slowed or speeded up to fine tune
long term accuracy to within three minutes per
year.
•
CLOCK SETTINGS
= Printout includes date,
time, weekday, and clock speed.
•
CLOCK SPEED
= The clock can be adjusted to
allow faster/slower speeds and therefore
increasing clock accuracy.
CODE
= Numeric sequence of numbers (such as:
1234) entered at the keypad. If Star-Enter-Key is
required, must be followed by a [
:
] key.
•
BASIC USER CODE
= User Codes assigned to
User Numbers 12+ (except Users 297-300).
(Does not allow programming)
•
INSTALLER CODE
= User Codes assigned to
User Numbers 2 and 3. (Allows all programming
except Master functions).
•
INVALID CODE
= A User Code that has not been
programmed in the lock.
•
MANAGER CODE
= User Codes assigned to
User Numbers 4 through 6. (Allows most of the
programming functions).
•
MASTER CODE
= User Code assigned to User
Number 1. Default (factory) Master Code is
123456. The User with the Master Code has
complete control of the lock.
•
PRINT ONLY USER CODE
= User Code as-
signed to Users 10 and 11. (Allows no
programming except print functions).
•
QUICK ENABLE USER 300 CODE
= Refers to
the User Code entered by User 297 which
(when entered at the keypad) enables the User
Code assigned to User 300 for one time only.
•
QUICK PC ACCESS CODE
= Permits upload/
download to DL-Windows Software on IBM/
compatible computer running Microsoft Windows
95, 98, or NT 4.0. Refers to the User Code for
User 298.
•
SERVICE CODE
= User 300 User Code. Allows
only one entry, then needs to be re-enabled by
the User 297 User Code to regain access.
•
SUPERVISOR CODE
= User Codes assigned to
Users 7, 8 and 9. Can only program day-to-day
operation.
•
USER CODE
= Code used by Users. Code is 3
to 6 numeric digits long, allowing controlled
entry.
•
VALID CODE
= An entered User Code that has
been programmed in the device.
COM PORT
= A computer serial communications port
used to communicate with the Lock and/or Data
Transfer Module.
DATA TRANSFER MODULE
= A device that permits
transfer of program/data between a computer and
the lock.
DATE
= Month, Day and Year entered as MMDDYY.
DAY OF WEEK
= Sunday through Saturday (where 1
= Sunday and 7 = Saturday).
DEFAULT
= Default settings are the original settings
that were set at the factory; in other words, it is the
lock's original factory condition when the lock was
first taken out of its box. The default settings are
permanently encoded within the lock's fixed mem-
ory, and when the lock is first started, or when
power is removed and re-applied (see Wiring and
Power-Up, page 11), the original factory default set-
tings are re-loaded and take effect.
DISABLE
= Turn off.
DOOR NUMBER
= Identification of each door with a
specific number (1-96). (Used with AL-DTM
Transfer Module)
DOWNLOAD
= Send data to lock or AL-DTM.
ENABLE
= Turn on.
EVENTS
= Recorded lock activity.
FUNCTION
(also called
Programming Functions
) =
are the numbers used to program lock features
(enabling/disabling Users, User Groups, Passage
Mode, Schedules, etc.).
GROUP
•
USER GROUP
= Defining a User to specific
Groups, allows User entry when the Group is
allowed entry.
•
GROUP 1 DISARMS BURGLAR CONTROL
= A
Group 1 USER CODE entry can disarm an
Glossary
