background image

36 

ALARM LOCK SYSTEMS, INC. (ALARM LOCK) 
warrants its products to be free from manufacturing 
defects in materials and workmanship for 24 months 
following the date of manufacture. ALARM LOCK will, 
within said period, at its option, repair or replace any 
product failing to operate correctly without charge to the 
original purchaser or user. 

This warranty shall not apply to any equipment, or any 
part thereof, which has been repaired by others, 
improperly installed, improperly used, abused, altered, 
damaged, subjected to acts of God, or on which any 
serial numbers have been altered, defaced or removed. 
Seller will not be responsible for any dismantling or 
reinstallation charges. 

THERE ARE NO WARRANTIES, EXPRESS OR 
IMPLIED, WHICH EXTEND BEYOND THE 
DESCRIPTION ON THE FACE HEREOF. THERE IS 
NO EXPRESS OR IMPLIED WARRANTY OF 
MERCHANTABILITY OR A WARRANTY OF FITNESS 
FOR A PARTICULAR PURPOSE. ADDITIONALLY, 
THIS WARRANTY IS IN LIEU OF ALL OTHER 
OBLIGATIONS OR LIABILITIES ON THE PART OF 
ALARM LOCK. 

Any action for breach of warranty, including but not 
limited to any implied warranty of merchantability, must 
be brought within the six months following the end of 
the warranty period. IN NO CASE SHALL ALARM 
LOCK BE LIABLE TO ANYONE FOR ANY 
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR 
BREACH OF THIS OR ANY OTHER WARRANTY, 
EXPRESS OR IMPLIED, EVEN IF THE LOSS OR 
DAMAGE IS CAUSED BY THE SELLER'S OWN 
NEGLIGENCE OR FAULT. 

In case of defect, contact the security professional who 
installed and maintains your security system. In order 
to exercise the warranty, the product must be returned 
by the security professional, shipping costs prepaid and 
insured to ALARM LOCK. After repair or replacement, 
ALARM LOCK assumes the cost of returning products 
under warranty. ALARM LOCK shall have no obligation 
under this warranty, or otherwise, if the product has 
been repaired by others, improperly installed, 
improperly used, abused, altered, damaged, subjected 
to accident, nuisance, flood, fire or acts of God, or on 
which any serial numbers have been altered, defaced 
or removed. ALARM LOCK will not be responsible for 
any dismantling, reassembly or reinstallation charges. 

This warranty contains the entire warranty. It is the sole 
warranty and any prior agreements or representations, 
whether oral or written, are either merged herein or are 
expressly canceled. ALARM LOCK neither assumes, 
nor authorizes any other person purporting to act on its 

behalf to modify, to change, or to assume for it, any 
other warranty or liability concerning its products. 

In no event shall ALARM LOCK be liable for an amount 
in excess of ALARM LOCK's original selling price of the 
product, for any loss or damage, whether direct, 
indirect, incidental, consequential, or otherwise arising 
out of any failure of the product. Seller's warranty, as 
hereinabove set forth, shall not be enlarged, diminished 
or affected by and no obligation or liability shall arise or 
grow out of Seller's rendering of technical advice or 
service in connection with Buyer's order of the goods 
furnished hereunder. 

ALARM LOCK RECOMMENDS THAT THE ENTIRE 
SYSTEM BE COMPLETELY TESTED WEEKLY. 

Warning: Despite frequent testing, and due to, but not 
limited to, any or all of the following; criminal tampering, 
electrical or communications disruption, it is possible for 
the system to fail to perform as expected. ALARM 
LOCK does not represent that the product/system may 
not be compromised or circumvented; or that the 
product or system will prevent any personal injury or 
property loss by burglary, robbery, fire or otherwise; nor 
that the product or system will in all cases provide 
adequate warning or protection. A properly installed 
and maintained alarm may only reduce risk of burglary, 
robbery, fire or otherwise but it is not insurance or a 
guarantee that these events will not occur. 
CONSEQUENTLY, SELLER SHALL HAVE NO 
LIABILITY FOR ANY PERSONAL INJURY, 
PROPERTY DAMAGE, OR OTHER LOSS BASED ON 
A CLAIM THE PRODUCT FAILED TO GIVE 
WARNING. Therefore, the installer should in turn 
advise the consumer to take any and all precautions for 
his or her safety including, but not limited to, fleeing the 
premises and allege police or fire department, in order 
to mitigate the possibilities of harm and/or damage. 

ALARM LOCK is not an insurer of either the property or 
safety of the user's family or employees, and limits its 
liability for any loss or damage including incidental or 
consequential damages to ALARM LOCK's original 
selling price of the product regardless of the cause of 
such loss or damage. 

Some states do not allow limitations on how long an 
implied warranty lasts or do not allow the exclusion or 
limitation of incidental or consequential damages, or 
differentiate in their treatment of limitations of liability for 
ordinary or gross negligence, so the above limitations 
or exclusions may not apply to you. This Warranty 
gives you specific legal rights and you may also have 
other rights which vary from state to state. 

ALARM LOCK LIMITED WARRANTY

 

Summary of Contents for PDL5300





































Reviews: