QUICK GUIDE ORYYONE CCTALK
-
PULSE
ENG
N° SW
DIP-SWITCH FUNCTIONS
SW 1
OFF
High selectivity – High security
ON
High acceptance – Low security
SW 2
OFF
Anti-fraud, warning enabled: 5 at temporary
inhibit (see ** in Table AF Modes below)
ON
Anti-fraud, warning disabled
(see * in Table AF Modes below)
SW 3
e
SW 4
SW 3
SW 4
Set up of slot luminescence
OFF
OFF
Changing colours
ON
OFF
Green
OFF
ON
Blue
ON
ON
White
SW 5
Serial modes (Dip-Sw8=OFF)
Pulse Mode (Dip-Sw8=ON)
SW 5
Function
SW 5
Pulse width
OFF
n.d.
OFF
100msec./100msec.
ON
n.d.
ON
200msec./200msec.
SW 6
e
SW 7
Serial modes (Dip-Sw8=OFF)
Pulse Mode (Dip-Sw8=ON)
SW 6
SW 7
Operating mode (protocol)
SW 6
SW 7
Pulse number
OFF
OFF
ccTalk
OFF
OFF
5 Euro = 1 pulse
ON
OFF
n.d.
ON
OFF
5 Euro = 5 pulses
OFF
ON
n.d.
OFF
ON
10 Euro = 5 pulses (5 € disabled) [v. 2.02 up]
ON
ON
n.d.
ON
ON
5 Euro = 10 pulses [v. 2.02 up]
SW 8
OFF
Serial mode (Select by Dip-switch 6 + 7: ex. ccTalk: SW6=OFF e SW7=OFF)
ON
Pulse mode
Please pay attention: after any change in the DS settings, power must be turned off and then on again, so that the validator can detect the set operation mode.
CCTALK COMMANDS
CcTalk supported specifications list
1. cctalk Generic Specification Issue 3.2
2. cctalk Expansion for Bill Validators Issue2.1
CcTalk supported commands list
1. Core Commands
Header 192 - Request build code
Header 244 - Request product code
Header 245 - Request equipment category id
Header 246 - Request manufacturer id
Header 254 - Simple poll
2. Core Plus Commands
Header 001 - Reset device
Header 004 - Request comms revision
Header 241 - Request software revision
Header 242 - Request serial number
3. Bill Validator Commands
Header 145 - Request currency revision
Header 152 - Request bill operating mode
Header 153 - Modify bill operating mode
Header 154 - Route bill
Header 156 - Request country scaling factor
Header 157 - Request bill id
Header 159 - Read buffered bill events
Header 197 - Calculate ROM checksum
Header 213 - Request Option flags
Header 216 - Request data storage availability
Header 227 - Request inhibit status
Header 228 - Modify master inhibit status
Header 230 - Request inhibit status
Header 231 - Modify inhibit status
Header 247 - Request variable set
L
UMINESCENT
S
IGNALS
AF
M
ODES
(A
NTI
-
FRAUD
)
NR RED
FLASHES
D
ESCRIPTION
1
V
ALIDATOR IS OPEN
2
J
AMMED BANKNOTE
3
F
RAUD ATTEMPTED
5
A
DJUST OPTICS
7
-
9
L
OW POWER SUPPLY
11
C
HECK ENCODER
+
MOTOR EFFICIENCY
12
-
14
ROM
ERROR
CONNECTOR PIN-OUT
(*) Dip-Switch SW2 ON
After fraud attempts, the validator returns the banknote. No signal given.
(**) Dip-Switch SW2 OFF
Attempt
Validator reaction
Do as described below
1°
Remains in service
-
2°
Remains in service
-
3°
> error (3 red flashes)
Reset (switch off then on)
… 4° …
> error (3 red flashes)
Reset (switch off then on)
After the 5th fraud attempt (3 yellow flashes), it is necessary to wait for automatic
restore of service. Take care not to switch the device off.
