Alcatel Omni Switch/Router User Manual Download | Manualshive

Page: 494 / 1100

background image

Configuring Source Route to Transparent Bridging

Page 17-46

Viewing the RIF Table

A Routing Information Field (RIF) is stored for each MAC address learned on a token ring
port. One RIF is stored for each MAC address. The maximum size of each RIF is 32 bytes
(long enough to traverse 15 bridge hops)

Once a RIF is learned for a MAC address, it is maintained until the MAC address is aged out
of the CAM. You can view a list of RIFs using the

srtbrif

command. To view the RIF table

follow these steps:

1.

Enter the

srtbrif

command at the menu prompt. The following prompt is displayed:

Enter MAC address ([XXYYZZ:AABBCC] or return for none) :

Enter the MAC address for which you want to see the RIF and press

<return>

, or enter a

<return>

without a MAC address to list all RIFs.

2.

Once you enter a MAC address (or

<return>

), the following prompt appears:

Enter Group ID (return for all Group) :

Enter a group ID and press

<return>

, or enter a

<return>

without a group ID to list the RIFs

for all groups.

3.

Once you enter the group ID (or

<return>

), a screen similar to the following appears:

Group

Non-Canonical

CAM

Port

ID

MAC Address

Indx

Len

RIF

---------------- ---------------

-----------------------

--------

------

-------------------------

4/ 1/Brg/ 1

2 10009E:4B7DE1

010E

6

0610:1231:0010:

Field Descriptions

The following section describes the fields shown using the

srtbrif

command.

Port

. This field lists the slot, port number, service type, and instance number for where the

RIF was learned for this MAC address.

Group ID

. The group number with which this RIF is associated.

Non-Canonical MAC Address

. The MAC address for this RIF. It is shown in non-canonical form.

CAM Indx

. The index number in the Content-Addressable Memory (CAM), where the MAC

addresses are stored, in hexadecimal form.

Len

. The length of the RIF packet, in bytes.

RIF

. The RIF address for this MAC address.

«
...
492
493
494
495
496
...
»

Summary of Contents for Omni Switch/Router













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Omni Switch/Router

Brand: Xantrex Pages: 8

Brand: Patton electronics Pages: 75

RocketLink-G 3088/I

Brand: Patton electronics Pages: 61

Brand: Patton Pages: 12

Brand: Patton Pages: 84

OnSite 3210 Series

Brand: Patton Pages: 110

Brand: Patton electronics Pages: 2

SMARTNODE 4110 Series

Brand: Patton electronics Pages: 78

Brand: Patton electronics Pages: 8

Brand: iDirect Pages: 52

Brand: Ruckus Wireless Pages: 56

IMACS Network Device

Brand: Zhone Pages: 114

Brand: H3C Pages: 9

Brand: TP-Link Pages: 37

Brand: Tenda Pages: 120

HomePNA PCI Adapter

Brand: City-Netek Pages: 18

OmniTik UPA-5HnD

Brand: RouterBOARD Pages: 4

Brand: Valcom Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands