Viewing Port Errors
Page 19-55
Viewing Port Errors
The
ve
command displays port error statistics for ports in the switch. Entering
ve
displays error statistics for all virtual ports in the switch. You can also display errors statistics
for only ports in a specific Group by specifying the Group ID after the
ve
command. For
example, to view errors only for ports in Group 6, you would enter
ve 6
You can also display error statistics for a specific port by entering the slot and port number
after the
ve
command. For example, to view errors only for Port 1 on the module in Slot 4,
you would enter
ve 4/1
The same type of information is displayed for a single Group or port as is displayed for all
ports in a switch. The following screen shows a sample from the
ve
command when speci-
fied without any Group or port parameters.
Virtual Interface Error Information- For All Interfaces
Slot/ Service/
Buffer Discards
Error Discards
Group Intf
Instance
In
Out
In
Out
===== === =========== =========== =========== ============ =============
2 All
Rtr/
1
3 All
Rtr/
2
1 All
Rtr/
1
1 3/1 Tnk/ 1
0
0
0
0
1 4/1
Brg/ 1
0
0
0
0
1 4/2
Brg/ 1
0
0
0
0
1 4/3
Brg/ 1
0
0
0
0
1 4/4
Brg/ 1
0
0
0
0
1 4/5
Brg/ 1
0
0
0
0
1 4/6
Brg/ 1
0
0
0
0
1 4/7
Brg/ 1
0
0
0
0
1 4/8
Brg/ 1
0
0
0
0
1 5/1
Brg/ 1
0
0
0
0
Group, Slot/Intf.
These columns are described for the
vi
command on page 19-50.
Service/Instance.
The Service Type (
Service
) and Instance (
Instance
) of this Service Type in the
switch. Service Type values are as follows:
•
Rtr
Virtual router port
•
Brg
Virtual bridge port
•
Tnk
Virtual trunk port (used for
WAN
)
•
T10
802.10 FDDI
service port
•
FRT
Frame Relay trunk port
•
Lne
LAN
Emulation service port
•
Vlc
VLAN clusters (X-LANE) service port
•
CIP
Classical IP service port
Summary of Contents for Omni Switch/Router
