Defining and Configuring AutoTracker Policies
Page 20-8
Defining a Protocol Policy
After you enter the Administrative Status for this mobile group or AutoTracker
VLAN
, the
following menu displays:
Select rule type:
1. Port Rule
2. MAC Address Rule
21) MAC Address Range Rule
3. Protocol Rule
4. Network Address Rule
5. User Defined Rule
6. Binding Rule
7. DHCP PORT Rule
8. DHCP MAC Rule
81) DHCP MAC Range Rule
Enter rule type (1):
1.
Press
3
and press
<Enter>
.
2.
The following prompt displays:
Set Rule Admin Status to ((e)nable/(d)isable):
Indicate whether or not you want to enable this rule. Type
e
to enable or
d
to disable. If
you enable the rule, the mobile group or AutoTracker
VLAN
will use it to determine
membership of devices. If you disable the rule, then this rule will not be used in assign-
ing devices, but the parameters you set up will be saved. The Admin Status for a Policy is
different from the Admin Status for the mobile group or AutoTracker
VLAN
as it controls
only to this specific rule. You can enable or disable the rule at a later time using the
modatvl
command.
3.
The following prompt displays:
Select Protocol:
1. IP
2. IPX
3. DECNET
4. APPLETALK
5. Protocol specified by ether-type
6. Protocol specified by DSAP and SSAP
7. Protocol specified by SNAP
Enter protocol type (1):
Enter the number for the protocol that will be used to define this mobile group or
AutoTracker
VLAN
. Numbers are listed next to the protocol names. By selecting a specific
protocol, you are indicating that all traffic originating from network devices using that
protocol will be assigned to this mobile group or AutoTracker
VLAN
. You can select the
IP
,
IPX
,
DECNET
, and
APPLETALK
protocols by entering 1, 2, 3, or 4, respectively.
♦
Please Take Note
♦
ARP
(address resolution protocol) is included as
IP
.
DDP
(datagram delivery protocol) and
AARP
(Apple-
Talk
ARP
) are included as AppleTalk.
DECNET
is
DECNET
Phase IV traffic only.
Summary of Contents for Omni Switch/Router
